Bedienungsanleitung Bosch GAS 18V-10 L (Seite 19 von 221) (Alle Sprachen)

786180

Zoom out

Zoom in

Vorherige Seite

1/221

Nächste Seite

English | 19

Switching On and Off

To switch on the dust extractor, briefly press the on/off

button(3).

To switch off the dust extractor, press the on/off button(3)

again.

For safety reasons, the dust extractor does not switch on if

the on/off button(3) is held down for longer than five

seconds.

Dry Vacuuming

Extracting dust that accumulates from working power

tools (seefigureG)

uThere must be a sufficient air exchange rate (L) in the

room when the exhaust air comes back into the room.

Be aware of the corresponding national regulations.

– Fit the dust extraction adapter(14) or the curved

nozzle(15) (see "Fitting the extraction adapter or curved

nozzle (seefigureD)", page18).

– Insert the extraction adapter(14) or the curved

nozzle(15) into the power tool's dust extraction outlet.

Only when using the dust extraction adapter(14):

Note: When working with power tools that have a low air

feed into the vacuum hose (e.g. jigsaws, sanders, etc.), the

false air intake(32) of the dust extraction adapter(14) must

be opened. This will improve the total output of the dust ex-

tractor and the power tool. To do this, turn the ring above

the false air intake(32) until the opening is at its maximum

size.

Wet Vacuuming

uDo not use the vacuum cleaner to vacuum combustible

or explosive liquids, such as petrol, oil, alcohol or

solvents. Do not vacuum hot, burning or explosive

dust. Do not operate the vacuum cleaner in areas sub-

ject to explosion hazards. Dust, vapours and liquids can

ignite or explode.

Before wet vacuuming:

– Empty the container (1).

– Clean the filter(33) and fit it back into the dust ex-

tractor(see "Cleaning/replacing filters (see figures I1–

I2)", page19).

The dust extractor is equipped with a float(34). Extraction

is stopped when the maximum filling level is reached.

After wet vacuuming, always:

– Empty the container (1).

– Empty the water from the filter (33).

To prevent mould growth after wet vacuuming:

– Remove the dust extractor lid (5) and leave it to dry thor-

oughly.

– Remove the filter (33) and also leave this to dry thor-

oughly (see "Cleaning/replacing filters (see figures I1–

I2)", page19).

Maintenance and Servicing

Maintenance and Cleaning

uRemove the battery before cleaning or performing

maintenance on the dust extractor, making tool ad-

justments, changing accessories or placing the dust

extractor in storage. This safety measure prevents the

dust extractor from being started accidentally.

uTo ensure safe and efficient operation, always keep

the dust extractor and the ventilation slots clean.

For the user to carry out maintenance, the dust extractor

needs to be disassembled, cleaned and maintained as far as

this is possible without endangering maintenance personnel

or other persons. Before disassembly, the dust extractor

should be cleaned to prevent any potential hazards. The

room/enclosure in which the dust extractor is disassembled

should be well ventilated. Wear personal protective equip-

ment while carrying out maintenance. After completing

maintenance, the maintenance area should be cleaned.

An inspection regarding the dust extraction capability must

be carried out at least once a year by the manufacturer or

someone who has been trained, e.g. to check for filter dam-

age, that the dust extractor is tight and that the control unit

is functioning correctly.

Class L dust extractors which were located in dirty environ-

ments should have their exteriors, as well as all their com-

ponents, cleaned or treated with sealant. When performing

maintenance and repair work, all dirty parts that cannot be

cleaned satisfactorily must be disposed of. Such parts must

be disposed of in impermeable bags in accordance with the

valid provisions for disposing of such waste.

– Clean the housing of the dust extractor occasionally with

a damp cloth.

– Clean dirty charging pins using a dry cloth.

Cleaning the container (see figures H1–H2)

Clean the container (1) after each use in order to ensure that

the dust extractor continues to perform optimally.

– Open the catches (2) and remove the dust extractor lid

(5).

– Shake out the container (1) over a suitable waste bin.

– If necessary, clean the container with a damp cloth.

Clean the filter if required (see "Cleaning/replacing filters

(see figures I1–I2)", page19).

– Replace the dust extractor lid (5) and close the catches

(2).

Cleaning/replacing filters (see figures I1–I2)

Suction power is dependent on the condition of the filter.

Therefore, the filter should be cleaned regularly.

Replace any damaged filters immediately.

– Open the catches(2) and remove the dust extractor lid

(5).

– Turn the filter(33) as far as it will go in the direction of ro-

tation and remove it from the filter bracket(35).

– If the filter is dry:

Tap the filter(33) on the side of a suitable waste bin.

Bosch Power Tools 1 609 92A 7MV | (12.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GAS 18V-10 L Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info