Bedienungsanleitung Bosch GBH 18V-26 F (Seite 21 von 297) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708068

Zoom out

Zoom in

Vorherige Seite

1/297

Nächste Seite

English | 21

Inserting the quick-change chuck (seefigureD)

u Use only model-specific original equipment and pay

attention to the number of identification grooves

(25). Only quick-change chucks with two or three

identification grooves are permitted. If an unsuitable

quick-change chuck is used, the application tool can fall

out during operation.

– Before insertion, clean the quick-change chuck and lightly

grease the shank.

– Wrap your whole hand around the SDS-plus quick-change

chuck (2) or the keyless quick-change chuck (1). Use a

turning motion to push the quick-change chuck into the

drill chuck holder (24) until you hear it click into place.

– The quick-change chuck is automatically locked. Check

that it is locked by pulling on the quick-change chuck.

Changing the Tool

The dust protection cap (4) largely prevents the penetration

of drilling dust into the tool holder during operation. When

inserting the tool, make sure that the dust protection cap (4)

does not become damaged.

u Replace a damaged dust protection cap immediately.

It is recommended that you have use an after-sales

service for this.

Changing the tool (SDS plus)

Inserting the SDS plus application tool (seefigureE)

The SDS-plus drill chuck enables you to change the applica-

tion tool easily and conveniently without needing to use ad-

ditional tools.

– GBH18V-26F: Insert the SDS plus quick-change

chuck(2).

– Clean and lightly grease the shank of the application tool.

– Insert the application tool into the tool holder while turn-

ing it until it locks automatically.

– Check that it is locked by pulling on the tool.

As a requirement of the system, the SDS-plus application

tool can move freely. This causes a certain radial run-out at

no-load, which has no effect on the accuracy of the drill hole,

as the drill bit centres itself upon drilling.

Removing SDS-plus application tools (seefigureF)

– Push the locking sleeve (5) back and remove the applica-

tion tool.

Changing the tool (without SDS plus)

(GBH18V-26)

Inserting the application tool (seefigureG)

Note: Application tools that do not have SDS plus must not

be used for hammer drilling or chiselling. Tools without SDS

plus and their drill chucks are damaged by hammer drilling

or chiselling.

– Insert a keyed chuck(22).

– Open the keyed chuck(22) by turning it until the tool can

be inserted. Insert the tool.

– Insert the chuck key(26) into the corresponding holes of

the keyed chuck(22) and clamp the tool evenly.

– Turn the impact/mode selector switch(16) to the

"drilling" position.

Removing the application tool (seefigureH)

– Use the chuck key(26) to turn the sleeve of the keyed

chuck(22) anticlockwise until the application tool can be

removed.

Changing the tool (without SDS plus)

(GBH18V-26F)

Inserting the application tool (seefigureI)

Note: Application tools that do not have SDS plus must not

be used for hammer drilling or chiselling. Tools without SDS

plus and their drill chucks are damaged by hammer drilling

or chiselling.

– Insert the keyless quick-change chuck(1).

– Hold the retaining ring(28) of the keyless quick-change

chuck firmly in place. Open the tool holder by turning the

front sleeve(27) until the tool can be inserted. Hold the

retaining ring(28) in place and firmly tighten the front

sleeve(27) by turning it in the direction of the arrow until

you hear it click into place.

– Check that it is seated securely by pulling on the tool.

Note: If the tool holder was unscrewed all the way, a scrap-

ing sound may be heard while retightening the tool holder

and it may not fully tighten.

In this case, turn the front sleeve(27) in the opposite direc-

tion to the arrow by one full turn. This will allow the tool

holder to be fully tightened.

– Turn the impact/mode selector switch (16) to the

"drilling" position.

Removing the application tool (seefigureJ)

– Hold the retaining ring(28) of the keyless quick-change

chuck firmly in place. Open the tool holder by turning the

front sleeve(27) in the direction of the arrow until the

tool can be removed.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

Bosch Power Tools 1 609 92A 5GC | (14.11.2019)

Bosch GBH 18V-26 F Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info