Bedienungsanleitung Bosch GBH 2-24 DSE Professional (Seite 18 von 22) (Deutsch, Portugiesisch, Spanisch)

591860

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Setting the Direction of Rotation GBH 2-24 DSR

With the right/left rotation switch 10, the rotational

direction of the machine can be changed.

Change the direction of rotation only when the

machine is switched off! Otherwise, the machine

can be damaged.

Right rotation:

Press the right/left switch 10 to the right to the stop.

Left rotation:

Press the right/left switch 10 to the left to the stop.

Set the direction of rotation for hammer drilling and

drilling always for right rotation.

Mode selection switch

Set the impact stop switch 7 to Drilling (only

activate when the drill is at a standstill).

Press the release button 6 on the mode selector

switch 7 and move the button to the desired position.

Drilling /

Screw

Driving

Hammer

Drilling

Vario-Lock Chiselling

GBH 2 S

GBH 2 - 24 DSE

GBH 2 - 24 DSR

GBH 2 S

GBH 2 - 24 DSE

GBH 2 - 24 DSR

GBH 2 - 24 DSE

GBH 2 - 24 DSR

GBH 2 - 24 DSE

GBH 2 - 24 DSR

The following table shows how the mode selection

switch 7 as well as the On/Off switch 8 for regulation

the speed (GBH 2-24 DSE) are to be set for the

various operating modes (see illustrations on the

fold-out page).

Operating mode GBH

2-S 2-24 DSE 2-24DSR

Hammer drilling in

Concrete or stone Fig. A Fig. C Fig. G.

Drilling in steel or wood Fig. B Fig. D Fig. H.

Screw driving

Right rotation - Fig. E Fig. I.

Left rotation - - Fig. J.

Chiseling - Fig. F Fig, K.

Setting the chisel position (VARIO-LOCK)

The percussion drill (GBH 2-24 DSE /

DSR) is suitable for light-duty chiseling

work. Operator fatigue can be avoided by

rotating the tool (e.g. flat chisel) to the

optimum position for use. The tool mount

can be set to 36 different positions.

Always wear protective gloves!

Insert the tool into the tool mount.

Press release button 6 and turn the mode selector

switch 7 to Chisel adjustment. (Fig. L ) When the

mode selector switch is in the Vario-lock position, the

tool mount can be rotated to the desired position.

To fix the tool mount in position, turn the mode

selector switch until it engages in the Chiseling

setting.

Always set the mode selector switch 7 to

Chiseling when carrying out chiseling.

Overload clutch

If the drill becomes caught or jammed, the drive to

the drill spindle is interrupted.

Because of the forces that occur as a result, always

hold the machine securely with both hands and take

a firm stance.

Sharpening chisels

Since good results can only be achieved using sharp

chisels, it is important to sharpen tools in good time.

This prolongs the life drilling depth. As a result the

vacuum attachment head always of your tools and

ensures high efficiency.

Grind chisels using grinding wheels (e.g. corundum).

Keeping the chisels wet using a steady supply of

water. Refer to the drawings below for recommended

values. Make sure that no annealing colour appears

on the cutting edges, otherwise the hardness of the

chisel will be impaired (Fig. R , S , T ).

Dust extraction

Dust extraction prevents large accumulations of dust,

high concentrations of dust in the ambient air and

facilitates disposal.

The appliance can be plugged directly into the

socket of a Bosch all-purpose vacuum cleaner which

incorporates a remote control Saugfix start device.

Attach vacuum attachment (accessory) and connect

the vacuum cleaner. The vacuum attachment springs

back as far as the preset drilling depth. As a result

the vacuum attachment head always remains close

to the surface.

Maintenance and cleaning

Before any work on the machine itself, pull the

mains plug.

For safe and proper working, always keep

the machine and the ventilation slots clean.

Clean the tool holder daily.

Replacing the Dust Protection Cap

Replace the dust protection cap 1 without delay if it

is damaged. A damaged dust protection cap can

allow dust to penetrate into the tool holder and lead

to malfunctions.

Have the replacement of the dust protection cap

performed by a customer service agent.

In extreme working conditions, conductive

dust can accumulate in the interior of the

machine when working with metal. The

protective insulation of the machine can be

de-graded. The use of a stationary extraction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GBH 2-24 DSE Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info