Bedienungsanleitung Bosch gbh 2 26 (Seite 22 von 139) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388862

Zoom out

Zoom in

Vorherige Seite

1/139

Nächste Seite

22 | English

1 619 929 726 | (14.11.07) Bosch Power Tools

Removing the Key Type Drill Chuck

Push the locking sleeve 5 toward the rear and

pull out the key type drill chuck 18.

Removing/Inserting the Quick Change

Chuck (GBH 2-26 DFR)

Removing the Quick Change Chuck

(see figure D)

Pull the lock ring for the quick change chuck 6

toward the rear, hold it in this position and pull

off the SDS-plus quick change chuck 2 or the

quick change keyless chuck 1 toward the front.

After removing, protect the replacement chuck

against contamination.

Inserting the Quick Change Chuck

(see figure E)

Before inserting, clean the quick change chuck

and apply a light coat of grease to the shank end.

Grasp the SDS-plus quick change chuck 2 or the

quick change keyless chuck 1 completely with

your hand. Slide the quick change chuck with a

turning motion onto the drill chuck mounting 20

until a distinct latching noise is heard.

The quick change chuck is automatically locked.

Check the locking effect by pulling the quick

change chuck.

Changing the Tool

The dust protection cap 4 largely prevents the

entry of drilling dust into the tool holder during

operation. When inserting the tool, take care

that the dust protection cap 4 is not damaged.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales service.

Inserting SDS-plus Drilling Tools (see figure F)

The SDS-plus drill chuck allows for simple and

convenient changing of drilling tools without the

use of additional tools.

GBH 2-26 DFR: Insert the SDS-plus quick change

chuck 2.

Clean and lightly grease the shank end of the tool.

Insert the tool in a twisting manner into the tool

holder until it latches itself.

Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus

drilling tool can move freely. This causes a cer-

tain radial run-out at no-load, which has no ef-

fect on the accuracy of the drill hole, as the drill

bit centres itself upon drilling.

Removing SDS-plus Drilling Tools

(see figure G)

Push back the locking sleeve 5 and remove the

tool.

Inserting Drilling Tools without SDS-plus

(GBH 2-26 E/RE/DE/DRE)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

Insert a key type drill chuck 18 (see “Changing

the Key Type Drill Chuck”, page 21).

Open the key type drill chuck 18 by turning until

the tool can be inserted. Insert the tool.

Insert the chuck key into the corresponding

holes of the key type drill chuck 18 and clamp

the tool uniformly.

GBH 2-26 E/RE: Set the selector switch 16 to

the “Drilling” symbol.

GBH 2-26 DE/DRE: Turn the mode selector

switch 11 to the “drilling” position.

Removing Drilling Tools without SDS-plus

(GBH 2-26 E/RE/DE/DRE)

Turn the sleeve of the key type drill chuck 18

with the drill chuck key in anticlockwise direc-

tion until the drilling tool can be removed.

Inserting Drilling Tools without SDS-plus

(GBH 2-26 DFR) (see figure H)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

Insert the quick change keyless chuck 1.

Firmly hold the retaining ring 22 of the quick

change chuck. Open the tool holder by turning

the front sleeve 21

until the tool can be inserted.

Tightly hold the retaining ring 22 and firmly turn

the front sleeve 21 in the direction of the arrow

until a distinct latching noise can be heard.

Check the tight seating by pulling the tool.

OBJ_BUCH-279-002.book Page 22 Wednesday, November 14, 2007 12:41 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbh 2 26 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info