388862
24
Zoom out
Zoom in
Vorherige Seite
1/139
Nächste Seite
24 | English
1 619 929 726 | (14.11.07) Bosch Power Tools
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Setting the Operating Mode
GBH 2-26 E/RE: With the selector switch for
drilling/hammer drilling 16, the operating mode
of the machine is selected.
To change the operating mode, press the re-
lease button 15 and turn the drilling/hammer
drilling selector switch 16 to the desired posi-
tion until it can be heard to latch.
GBH 2-26 DE/DRE/DFR: The operating mode of
the power tool is selected with the mode selec-
tor switch 11.
To change the operating mode, push the release
button 10 and turn the mode selector switch 11
to the requested position until it can be heard to
latch.
Note: Change the operating mode only when the
machine is switched off! Otherwise, the ma-
chine can be damaged.
Reversing the Rotational Direction
(GBH 2-26 RE/DRE/DFR)
The rotational direction switch 7 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 9 actuated.
Right rotation: Turn the selector switch for
drilling/hammer drilling 7 on both sides to
the stop in the position .
Left rotation: Turn the selector switch for
drilling/hammer drilling 7 on both sides to
the stop in the position .
Set the direction of rotation for hammer drilling,
drilling and chiselling always to right rotation.
Switching On and Off
To start the machine, press the On/Off switch 9.
To lock the On/Off switch, keep it pressed and
additionally push the lock-on button 8.
To switch off the machine, release the On/Off
switch 9. When the On/Off switch 9 is locked,
press it first and then release it.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on pow-
er tool can be variably adjusted, depending on
how far the On/Off switch 9 is pressed.
Light pressure on the On/Off switch 9 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
Safety Clutch
f If the tool insert becomes caught or
jammed, the drive to the drill spindle is in-
terrupted. Because of the forces that occur,
always hold the power tool firmly with both
hands and provide for a secure stance.
f If the power tool jams, switch the machine
off and loosen the tool insert. When switch-
ing the machine on with the drilling tool
jammed, high reaction torques can occur.
GBH 2-26 E/RE GBH 2-26 DE/DRE/DFR
Position for hammer
drilling in concrete or
stone
Position for drilling with-
out impact in wood, met-
al, ceramic and plastic as
well as for screwdriving
and thread cutting.
Vario-Lock position for
adjustment of the chisel-
ling position
The mode selector
switch 11 does not latch
in this position.
Position for chiselling
OBJ_BUCH-279-002.book Page 24 Wednesday, November 14, 2007 12:41 PM
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch gbh 2 26 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info