388862
25
Zoom out
Zoom in
Vorherige Seite
1/139
Nächste Seite
English | 25
Bosch Power Tools 1 619 929 726 | (14.11.07)
Working Advice
Changing the Chiselling Position (Vario-Lock)
(GBH 2-26 DE/DRE/DFR)
The chisel can be locked in 36 positions. In this
manner, the optimum working position can be
set for each application.
Insert the chisel into the tool holder.
Turn the mode selector switch 11 to the “Vario-
Lock” position (see “Setting the Operating
Mode”, page 24).
Turn the tool holder to the desired chiselling po-
sition.
Turn the mode selector switch 11 to the “chisel-
ling” position. The tool holder is now locked.
For chiselling, set the rotation direction to right
rotation.
Inserting Screwdriver Bits (see figure L)
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
To work with screwdriver bits, a universal bit
holder 29 with SDS-plus shank (accessory) is re-
quired.
Clean the shank end of the adapter shank and
apply a light coat of grease.
Insert the universal bit holder with a turning
motion into the tool holder until it automatically
locks.
Check the locking effect by pulling the universal
bit holder.
Insert a screwdriver bit into the universal bit
holder. Use only screwdriver bits that match the
screw head.
To remove the universal bit holder, pull the lock-
ing sleeve 5 toward the rear and remove the uni-
versal bit holder 29 out of the tool holder.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
f A damaged dust protection cap should be
changed immediately. We recommend hav-
ing this carried out by an after-sales service.
Clean the tool holder 3 each time after using.
WARNING! Important instructions for con-
necting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
Do not connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it
must be disposed of safely.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article
number given on the type plate of the machine.
OBJ_BUCH-279-002.book Page 25 Wednesday, November 14, 2007 12:41 PM
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch gbh 2 26 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info