Bedienungsanleitung Bosch gbh 36 vf li 2 (Seite 24 von 333) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388756

Zoom out

Zoom in

Vorherige Seite

1/333

Nächste Seite

24 | English

1 619 929 777 | (23.7.07) Bosch Power Tools

During the charging procedure, the three green

LEDs light up one after the other and briefly go

out. The battery is fully charged when the three

green LEDs light up continuously. The three

LEDs go out again approx. 5 minutes after the

battery has been fully charged.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A long

battery service life is achieved in this manner.

Auxiliary Handle

f Operate your machine only with the auxiliary

handle 18.

Rotating the Auxiliary Handle (see figure A)

The auxiliary handle 18 can be set to any position

for a secure and low-fatigue working posture.

Turn the bottom part of the auxiliary handle 18

in counterclockwise direction and swivel the

auxiliary handle 18 to the desired position. Then

retighten the bottom part of the auxiliary handle

18 by turning in clockwise direction.

Pay attention that the clamping band of the aux-

iliary handle is positioned in the groove on the

housing as intended for.

Adjusting the Drilling Depth (see figure B)

The required drilling depth X can be set with the

depth stop 17.

Press the button for the depth stop adjustment

12 and insert the depth stop into the auxiliary

handle 18.

The knurled surface of the depth stop 17 must

face downward.

Insert the SDS-plus drilling tool to the stop into

the SDS-plus tool holder 3. Otherwise, the mov-

ability of the SDS-plus drilling tool can lead to

incorrect adjustment of the drilling depth.

Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drilling

depth X.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus

tools are required that are inserted in the SDS-

plus drill chuck.

For drilling without impact in wood, metal, ce-

ramic and plastic as well as for screwdriving and

thread cutting, tools without SDS-plus are used

(e.g., drills with cylindrical shank). For these

tools, a keyless chuck or a key type drill chuck

are required.

GBH 36 VF-LI: The SDS-plus quick change chuck

2 can easily be replaced against the quick

change keyless chuck 1 provided.

Changing the Key Type Drill Chuck

(GBH 36 V-LI)

To work with tools without SDS-plus (e.g., drills

with cylindrical shank), a suitable drill chuck

must be mounted (key type drill chuck or key-

less chuck, accessories).

Mounting the Key Type Drill Chuck

(see figure C)

Screw the SDS-plus adapter shank 21 into a key

type drill chuck 20. Secure the key type drill

chuck 20 with the securing screw 19. Please ob-

serve that the securing screw has a left-hand

thread.

Inserting the Key Type Drill Chuck

(see figure D)

Clean the shank end of the adapter shank and

apply a light coat of grease.

Insert the key type drill chuck with the adapter

shank into the tool holder with a turning motion

until it automatically locks.

Check the locking effect by pulling the key type

drill chuck.

Removing the Key Type Drill Chuck

Push the locking sleeve 5 toward the rear and

pull out the key type drill chuck 20.

OBJ_BUCH-283-001.book Page 24 Monday, July 23, 2007 12:41 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbh 36 vf li 2 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info