Bedienungsanleitung Bosch gbh 36 vf li 2 (Seite 25 von 333) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388756

Zoom out

Zoom in

Vorherige Seite

1/333

Nächste Seite

English | 25

Bosch Power Tools 1 619 929 777 | (23.7.07)

Removing/Inserting the Quick Change

Chuck (GBH 36 VF-LI)

Removing the Quick Change Chuck

(see figure E)

Pull the lock ring for the quick change chuck 6

toward the rear, hold it in this position and pull

off the SDS-plus quick change chuck 2 or the

quick change keyless chuck 1 toward the front.

After removing, protect the replacement chuck

against contamination.

Inserting the Quick Change Chuck

(see figure F)

Before inserting, clean the quick change chuck

and apply a light coat of grease to the shank end.

Grasp the SDS-plus quick change chuck 2 or the

quick change keyless chuck 1 completely with

your hand. Slide the quick change chuck with a

turning motion onto the drill chuck mounting 22

until a distinct latching noise is heard.

The quick change chuck is automatically locked.

Check the locking effect by pulling the quick

change chuck.

Changing the Tool

The dust protection cap 4 largely prevents the

entry of drilling dust into the tool holder during

operation. When inserting the tool, take care

that the dust protection cap 4 is not damaged.

f A damaged dust protection cap should be

changed immediately. We recommend hav-

ing this carried out by an after-sales service.

Inserting SDS-plus Drilling Tools (see figure G)

The SDS-plus drill chuck allows for simple and

convenient changing of drilling tools without the

use of additional tools.

GBH 36 VF-LI: Insert the SDS-plus quick change

chuck 2.

Clean and lightly grease the shank end of the

tool.

Insert the tool in a twisting manner into the tool

holder until it latches itself.

Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus

drilling tool can move freely. This causes a cer-

tain radial run-out at no-load, which has no ef-

fect on the accuracy of the drill hole, as the drill

bit centres itself upon drilling.

Removing SDS-plus Drilling Tools

(see figure H)

Push back the locking sleeve 5 and remove the

tool.

Inserting Drilling Tools without SDS-plus

(GBH 36 V-LI)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

Insert a key type drill chuck 20 (see “Changing

the Key Type Drill Chuck”, page 24).

Open the key type drill chuck 20 by turning until

the tool can be inserted. Insert the tool.

Insert the chuck key into the corresponding

holes of the key type drill chuck 20 and clamp

the tool uniformly.

Turn the mode selector switch 10 to the “drill-

ing” position.

Removing Drilling Tools without SDS-plus

(GBH 36 V-LI)

Turn the sleeve of the key type drill chuck 20

with the drill chuck key in anticlockwise direc-

tion until the drilling tool can be removed.

Inserting Drilling Tools without SDS-plus

(GBH 36 VF-LI) (see figure I)

Note: Do not use tools without SDS-plus for

hammer drilling or chiselling! Tools without

SDS-plus and their drill chucks are damaged by

hammer drilling or chiselling.

Insert the quick change keyless chuck 1.

Firmly hold the retaining ring 24 of the quick

change chuck. Open the tool holder by turning

the front sleeve 23 until the tool can be inserted.

Tightly hold the retaining ring 24 and firmly turn

the front sleeve 23 in the direction of the arrow

until a distinct latching noise can be heard.

Check the tight seating by pulling the tool.

OBJ_BUCH-283-001.book Page 25 Monday, July 23, 2007 12:41 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbh 36 vf li 2 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info