Bedienungsanleitung Bosch gbm 1 re (Seite 21 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387119

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English | 21

Bosch Power Tools 1 609 929 V00 | (17.11.09)

Right rotation: Press the rotational direction

switch 7 through to the right stop (for drilling

and driving screws).

Left rotation: Press the rotational direction

switch 7 through to the left stop (for loosening

and unscrewing screws and nuts).

Gear Selection, Mechanical

f The gear selector 8 can be actuated at

standstill or when the machine is running.

However, this should not be done while op-

erating at full load or maximum speed.

Two speed ranges can be preselected with the

gear selector 8.

Gear I:

Low speed range; for working with large drilling

diameter or for driving in screws.

Gear II:

High speed range; for working with small drilling

diameter.

If the gear selector 8 cannot be fully engaged,

lightly rotate the drive spindle with the drill bit

by twisting the drill chuck.

Preselecting the Speed

(GBM 10-2 RE/GBM 13-2 RE)

The required speed can be preselected with the

thumbwheel 5 (also while running).

The required speed depends on the material to

be worked and the diameter of the tool. Deter-

mine the optimum setting through practical

testing.

Switching On and Off

To start the machine, press the On/Off switch 6

and keep it pressed.

To lock the pressed On/Off switch 6, press the

lock-on button 4.

To switch off the machine, release the On/Off

switch 6 or when it is locked with the lock-on

button 4, briefly press the On/Off switch 6 and

then release it.

Adjusting the Speed

(GBM 10-2 RE/GBM 13-2 RE)

The speed of the switched on power tool can be

variably adjusted, depending on how far the

On/Off switch 6 is pressed.

Light pressure on the On/Off switch 6 results in

a low rotational speed. Further pressure on the

switch results in an increase in speed.

Working Advice

f Apply the power tool to the screw/nut only

when it is switched off. Rotating tool inserts

can slip off.

For drilling in metal, use only perfectly sharp-

ened HSS drill bits (HSS=high-speed steel). The

appropriate quality is guaranteed by the Bosch

accessories program.

Twist drills from 2.5–10 mm can easily be

sharpened with the drill bit sharpener (see ac-

cessories).

We recommend the use of a drill stand (see ac-

cessories) for work where greater precision is

particularly required.

The machine vice, which is available as an acces-

sory, enables secure clamping of workpieces.

This prevents the workpiece from turning and

any accidents this would cause.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

OBJ_BUCH-321-002.book Page 21 Tuesday, November 17, 2009 9:01 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbm 1 re Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info