Bedienungsanleitung Bosch gbm 1 re (Seite 19 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

387119

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

English | 19

Bosch Power Tools 1 609 929 V00 | (17.11.09)

Declaration of Conformity

We declare under our sole responsibility that

the product described under “Technical Data” is

in conformity with the following standards or

standardization documents: EN 60745 accord-

ing to the provisions of the directives

2004/108/EC, 98/37/EC (until 28 Dec 2009),

2006/42/EC (from 29 Dec 2009).

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

04.11.2009

Assembly

Auxiliary Handle

(GBM 13-2/GBM 13-2 RE)

(see figure A)

f Operate your machine only with the auxilia-

ry handle 10.

The auxiliary handle 10 can be set to any posi-

tion for a secure and low-fatigue working pos-

ture.

Turn the bottom part of the auxiliary handle 10

in counterclockwise direction and swivel the

auxiliary handle 10 to the desired position. Then

retighten the bottom part of the auxiliary handle

10 by turning in clockwise direction.

Adjusting the Drilling Depth

The required drilling depth X can be set with the

depth stop 11.

Press the button for the depth stop adjustment

9 and insert the depth stop into the auxiliary

handle 10.

The knurled surface of the depth stop 11 must

face downward.

Pull out the depth stop until the distance be-

tween the tip of the drill bit and the tip of the

depth stop correspond with the desired drilling

depth X.

Changing the Tool

f Before any work on the machine itself, pull

the mains plug.

f Wear protective gloves when changing the

tool. The drill chuck can become very hot

during longer work periods.

Keyless Chuck (see figure B)

Hold the rear sleeve 3 of the keyless chuck 1

tight and turn the front sleeve 2 in rotation di-

rection n, until the tool can be inserted. Insert

the tool.

Hold the rear sleeve 3 of the keyless chuck 1

tight and firmly tighten the front sleeve 2 by

hand in rotation direction o, until the locking

action (click) is heard. The drill chuck is locked

automatically.

The locking is released again to remove the tool

when the front sleeve 2 is turned in the opposite

direction.

Key Type Drill Chuck (see figure C)

Open the key type drill chuck 14 by turning until

the tool can be inserted. Insert the tool.

Insert the chuck key 13 into the corresponding

holes of the key type drill chuck 14 and clamp

the tool uniformly.

Screwdriver Tools (GBM 10-2 RE/

GBM 13-2 RE) (see figure D)

The drill spindle 16 is equipped with a hexagon

socket for use with screwdriver bits. Dismount

the drill chuck and insert the screwdriver bit 15

directly into the drill spindle 16 where it is re-

tained by a securing ring.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

OBJ_BUCH-321-002.book Page 19 Tuesday, November 17, 2009 9:01 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gbm 1 re Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info