786454

Bosch GCO 14-24 J Seite 18

18
Zoom out
Zoom in
Vorherige Seite
1/255
Nächste Seite
18 | English
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
uAvoid starting the power tool unintentionally. The
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
Carefully remove all parts included in the delivery from their
packaging.
Remove all packing material from the power tool and the ac-
cessories provided.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Cut-off grinder with cutting disc fitted
– Hex key (12)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them properly repaired or replaced by an author-
ised service centre.
Stationary or flexible mounting
uTo ensure safe handling, the power tool must be
mounted on a flat, stable work surface (e.g. work
bench) before use.
Mounting on a work surface (see figure A)
– Use suitable screw fasteners to secure the power tool to
the work surface. Use the holes (11) to do this.
Flexible installation (not recommended)
In exceptional circumstances, if it is not possible to securely
mount the power tool on a work surface, you can improvise
by placing the feet of the base plate (13) on an appropriate
base (e.g. workbench, flat ground, etc.), without screwing
down the power tool.
Changing the Cutting Disc (seefiguresB1−B2)
uPull the plug out of the socket before carrying out any
work on the power tool.
uDo not activate the spindle lock (5) while the tool
spindle (22) is moving. The power tool may become
damaged if you do this.
uDo not touch the cutting disc after use until it has
cooled. The cutting disc becomes very hot during use.
Only use cutting discs that match the specifications given in
this operating manual and that have been tested and marked
in accordance with EN 12413.
Use any intermediate layers provided with the cutting disc.
Place unused cutting discs in an enclosed container or their
original packaging. Store the cutting discs lying flat.
Removing the cutting disc
– Bring the power tool into the work position.
– Swivel the retracting blade guard (4) backwards as far as
possible.
– Turn the hexagon screw (25) using the hex key (12)
provided while pressing the spindle lock (5) until it en-
gages.
– Hold the spindle lock down and unscrew the hexagon
screw (25).
– Remove the washer (24) and the clamping flange (23).
– Remove the cutting disc (6).
Fitting the cutting disc
If required, clean all the parts you want to fit before installing
them.
– Place the new cutting disc on the tool spindle (22) such
that the sticker points away from the tool arm.
– Fit the clamping flange (23), the washer (24) and the
hexagon screw (25). Press the spindle lock (5) until it en-
gages and retighten the hexagon screw (25) by turning it
clockwise. (Tightening torque approx. 18–20Nm)
– Slowly guide the retracting blade guard (4) all the way
down until the cutting disc is completely covered.
– Make sure that the retracting blade guard (4) is working
properly.
After fitting the cutting disc, check that the cutting disc is fit-
ted correctly and can turn freely before switching on the
power tool.
– Make sure that the cutting disc does not brush against the
retracting blade guard (4), the fixed protective guard
(20) or any other parts.
– Put the power tool into operation for approx. 30 seconds.
If there is substantial vibration, switch the power tool off
immediately, remove the cutting disc and then refit it.
Operation
uPull the plug out of the socket before carrying out any
work on the power tool.
Transport Safety Lock (see figure C)
The transport safety lock (17) makes it easier to handle the
power tool when transporting it to various working locations.
Unlocking the power tool (work position)
– Press the tool arm down slightly by the handle (3) to re-
lease the transport safety lock (17).
– Pull the transport safety lock (17) all the way out.
1 609 92A 7ND | (26.04.2022) Bosch Power Tools
… 18 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GCO 14-24 J wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info