Bedienungsanleitung Bosch GCO 14-24 J (Seite 19 von 255) (Alle Sprachen)

786454

Zoom out

Zoom in

Vorherige Seite

1/255

Nächste Seite

English | 19

– Slowly guide the tool arm upwards.

Note: Make sure that the transport safety lock is not pushed

in when working, otherwise the tool arm will not be able to

be swivelled to the required depth.

Locking the power tool (transport position)

– Guide the tool arm downwards until you can press the

transport safety lock (17) all the way in.

Further information about transporting (see "Transport",

page20).

Setting the Mitre Angle (see figure D)

The mitre angle can be set between 0° and 45°.

Important settings are marked with corresponding markings

on the angle guide (7). The 0° and 45° positions are secured

by the respective end stop.

– Loosen the locking screws (16) on the angle guide using

the hex key (12) (8mm) provided.

– Set the required angle and retighten both locking screws

(16).

Moving the Angle Guide (see figures D−E)

If you want to cut workpieces more than 140mm wide, you

can move the angle guide (7) backwards.

– Completely unscrew the locking screws (16) using the

hex key provided (12) (8mm).

– Move the angle guide (7) backwards by one or two holes

to the required distance.

– Set the required angle and retighten both locking screws

(16).

Clamping the workpiece

To ensure maximum safety while working, the workpiece

must always be firmly clamped.

Do not saw workpieces that are too small to clamp firmly.

Clamping the Workpiece (see figure E)

– Place the workpiece against the angle guide (7).

– Slide the locking spindle (8) against the workpiece and

clamp the workpiece in place using the spindle handle

(10).

Securing the Workpiece (cross section of max. 40 x 40

mm) (see figures F−H)

– Set the angle guide (7) to the standard 0° mitre/bevel

angle.

– Lift the workpiece support (15) slightly and slide it

through the slot in the angle guide.

– Hang the hook of the workpiece support in the opening of

the clamping jaw (14).

– Place the workpiece on the workpiece support (15).

– Slide the locking spindle (8) against the workpiece and

clamp the workpiece in place using the spindle handle

(10).

uEnsure that the workpiece support is securely connec-

ted to the clamping jaw and does not tip when you

place the workpiece on it.

uEnsure that the height of the workpiece on the work-

piece support is max. 40 mm. Taller workpieces can-

not be clamped securely in place.

uEnsure that the workpiece support is slid back com-

pletely into the angle guide after use. A protruding

hook prevents a workpiece from being securely

clamped.

Releasing the workpiece

– Release the spindle handle (10).

– Open the quick release (9) and pull the locking spindle

(8) away from the workpiece.

Start-up

uPay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the charger. Chargers marked 230 V can

also be operated at 220 V.

uProducts that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

uCheck the cutting disc before using it. The cutting disc

must be fitted properly and be able to rotate freely.

Carry out a test run for at least 30 seconds with no

load. Do not use cutting discs that are damaged, run

untrue or vibrate during use. Damaged cutting discs can

shatter and cause injuries.

The dust from materials such as lead paint, minerals and

metal can be harmful to human health. Touching or breath-

ing in this dust can trigger allergic reactions and/or cause

respiratory illnesses in the user or in people in the near vicin-

ity.

Certain kinds of metal dust are hazardous, especially in com-

bination with alloys such as zinc, aluminium or chrome. Ma-

terials containing asbestos may only be machined by special-

ists.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the materials being machined that apply

in the country of use must be observed.

The cutting disc can become blocked by dust, chips or frag-

ments of the workpiece in the recess of the base plate (13).

– Switch the power tool off and pull the mains plug out of

the socket.

– Wait until the cutting disc has come to a complete stop.

– Tilt the power tool backwards so that small pieces of the

workpiece can fall out of the opening designed for this

purpose.

If necessary, use a suitable tool to remove all the pieces of

workpiece.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Position of the operator

uDo not stand in front of the power tool in line with the

cutting disc. Always stand to the side of the cutting

Bosch Power Tools 1 609 92A 7ND | (26.04.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GCO 14-24 J Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info