Bedienungsanleitung Bosch GCO 2000 Professional (Seite 18 von 227) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592623

Zoom out

Zoom in

Vorherige Seite

1/227

Nächste Seite

18 | English

1 609 92A 0Y1 | (17.9.14) Bosch Power Tools

Stationary or Flexible Mounting

 To ensure safe handling, the machine must be mounted

on a level and stable surface (e. g., workbench) prior to

using.

Mounting to a Working Surface (see figure A)

– Fasten the power tool with suitable screw fasteners to the

working surface. The mounting holes 11 serve for this pur-

pose.

Flexible Mounting (not recommended!)

In the exceptional case that it should not be possible to firmly

bench-mount the power tool, you can provisionally place the

legs of base plate 12 on a suitable surface (e. g. a workbench,

level floor, etc.) without bolting the machine down.

Changing the Tool (see figures B1–B2)

 Before any work on the machine itself, pull the mains

plug.

 Actuate the spindle lock 5 only when the tool spindle

21 is stopped. Otherwise, the machine can become dam-

aged.

 Do not touch the cutting disc after working before it

has cooled. The cutting disc becomes very hot while work-

ing.

Use only cutting discs that have an equal or higher maximal al-

lowable speed than the no-load speed of your power tool.

Use only cutting discs that correspond to the characteristic

data given in these operating instructions and are checked ac-

cording to EN 12413 and marked appropriately.

Place unused cutting discs in an enclosed container or in the

original packaging. Store cutting discs lying flat.

Removing the Cutting Disc

– Bring the power tool into the working position. (see “Re-

leasing the Machine (Working Position)”, page 18)

– Swing back the retracting blade guard 4 to the stop.

– Turn hexagon bolt 24 with the provided ring spanner 14

(15 mm) and at the same time press the spindle lock 5 un-

til it engages.

– Hold the spindle lock pressed and unscrew the hexagon

bolt 24.

– Remove the washer 23 and the clamping flange 22.

– Remove the cutting disc 6.

Installing the Cutting Disc

If required, clean all parts to be mounted prior to assembly.

– Mount the new cutting disc onto the tool spindle 21 in such

a manner that its lable faces away from the tool arm.

–Mount the clamping flange 22, the washer 23 and the hex-

agon bolt 24.

Press spindle lock 5 until it engages and tighten hexagon

bolt 24 with the provided ring spanner 14. (Tightening

torque approx. 18–20 Nm)

– Slowly guide the retracting blade guard 4 down until the

cutting disc is covered off.

– Make sure that the retracting blade guard 4 operates prop-

erly.

After mounting the cutting disc and before switching on,

check whether the cutting disc is properly mounted and if it

can rotate freely.

– Make sure that the cutting disc does not graze against the

retracting blade guard 4, the blade guard 19 or against

other parts.

– Run the machine for approx. 30 seconds.

Should significant vibrations occur, switch off the machine

immediately; remove and install the cutting disc again.

Operation

 Before any work on the machine itself, pull the mains

plug.

Transport Safety (see figure C)

The transport safety-lock 15 enables easier handling of the

machine when transporting to various working locations.

Releasing the Machine (Working Position)

– Push the tool arm by the handle 3 down a little in order to

relieve the transport safety-lock 15.

– Pull the transport safety-lock 15 completely outward.

– Guide the tool arm slowly upward.

Note: When working, pay attention that the transport safety-

lock is not pushed inwards. Otherwise, the tool arm cannot be

lowered to the requested depth.

Securing the Machine (Transport Position)

– Guide the tool arm downward until the transport safety-

lock 15 can be pushed completely inward.

For additional information on transport, see page 20.

Adjusting the Cutting Angle (see figure D)

The miter angle can be set in a range from 0° to 45°.

Frequently used mitre angles are identified on the angle stop

7 with appropriate markings. The 0° and 45° position are set

at the respective end stop.

– Loosen the locking screws 13 for the angle stop with the

supplied ring spanner 14 (15 mm).

– Adjust the desired angle and firmly tighten both locking

screws 13 again.

Displacing the Angle Stop (see figure D and E)

When cutting workpieces wider than 140 mm, the angle stop

7 can be displaced to the rear.

– Completely unscrew locking screws 13 with the supplied

ring spanner 14 (15 mm).

– Move the angle stop 7 toward the rear by one or two holes

to the desired clearance.

– Adjust the desired angle and firmly tighten both locking

screws 13 again.

Clamping the Workpiece (see figure E)

To ensure optimum working safety, the workpiece must al-

ways be firmly clamped.

Do not saw workpieces that are too small to clamp.

Long workpieces must be underlaid or supported at their free

end.

OBJ_BUCH-1063-004.book Page 18 Wednesday, September 17, 2014 9:34 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GCO 2000 Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info