Bedienungsanleitung Bosch GCO 2000 Professional (Seite 19 von 227) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592623

Zoom out

Zoom in

Vorherige Seite

1/227

Nächste Seite

English | 19

Bosch Power Tools 1 609 92A 0Y1 | (17.9.14)

– Place the workpiece against the angle stop 7.

– Slide the clamping spindle 8 against the workpiece and

firmly clamp the workpiece with the spindle handle 10.

Loosening the Workpiece

– Loosen the spindle handle 10.

– Tilt up the quick release 9 and pull the clamping spindle 8

away from the workpiece.

Starting Operation

 Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate of

the machine.

 Check the cutting disc before using. The cutting disc

must be properly mounted and must rotate freely. Car-

ry out a 30 second (min.) test run with no load. Do not

use damaged, out-of-centre or vibrating cutting discs.

Damaged cutting discs can burst and cause injuries.

Dusts from materials such lead-containing coatings, minerals

and metal can be harmful to one’s health. Contact with or in-

haling the dusts can trigger allergic reactions to the operator

or bystanders and/or lead to respiratory infections.

Certain metal dusts are considered hazardous, especially in

conjunction with alloys such as zinc, aluminium or chromium.

Materials containing asbestos may only be worked by special-

ists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

The blade can be blocked by dust, chips or workpiece frag-

ments in the slot of the base plate 12.

– Switch the machine off and pull the mains plug from the

socket outlet.

– Wait until the cutting disc has come to a complete stop.

– Tilt the machine toward the rear, so that small workpiece

fragments can fall out of the opening intended for this pur-

pose.

If required, use a suitable tool to remove all workpiece frag-

ments.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Position of the Operator (see figure F)

 Do not stand in a line with the cutting disc in front of the

machine. Always stand aside of the cutting disc. This

measure provides for better protection of your body

against possible splinters in case of cutting disc breakage.

Switching On and Off (see figure G)

To save energy, only switch the power tool on when using it.

–To start the machine, firstly press the lock-off button 1.

Then press the On/Off switch 2 and keep it pressed.

Note: For safety reasons, the On/Off switch 2 cannot be

locked; it must remain pressed during the entire operation.

–To switch off the machine, release the On/Off switch 2.

Soft starting

The electronic soft starting feature limits the torque upon

switching on and increases the working life of the motor.

Working Advice

General Cutting Instructions

 Do not touch the cutting disc after working before it

has cooled. The cutting disc becomes very hot while work-

ing.

 Make sure that the spark guard 20 is properly mount-

ed. Sparking occurs when cutting metal.

Protect the cutting disc against impact, shock and grease. Do

not subject the cutting disc to lateral pressure.

Do not strain the power tool so heavily that it comes to a

standstill.

Excessive feed considerably reduces the performance capa-

bility of the machine and shortens the service life of the cut-

ting disc.

Use only cutting discs that are suitable for the material to be

worked.

Permissible Workpiece Dimensions

Maximum workpiece sizes:

Minimum workpiece sizes

(= all workpieces that can be clamped via the clamping spin-

dle 8): Length 80mm

Cutting depth, max. (0°/0°): 125 mm

Cutting Metal

– Set the desired mitre angle.

– Firmly clamp the workpiece as appropriate for its dimen-

sions.

– Switch on the machine.

– Slowly guide the tool arm downward with the handle 3.

– Cut the workpiece applying uniform feed.

– Switch the machine off and wait until the cutting disc

comes to a complete stop.

– Guide the tool arm slowly upward.

Mitre/Bevel Angle

Workpiece Form 0° 45°

125 Ø 100 Ø

110 x 110 82 x 82

180 x 85 90 x 75

130 x 130 75 x 75

OBJ_BUCH-1063-004.book Page 19 Wednesday, September 17, 2014 9:34 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GCO 2000 Professional Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info