Bedienungsanleitung Bosch GDE 18V-26 D (Seite 15 von 85) (Alle Sprachen)

786182

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

English | 15

Fitting the Stabilising Brackets (seefigureA)

– Push the stabilising bracket(11) all the way into the as-

sembly openings(22).

Fitting the Dust Extraction Attachment

(seefiguresB1−B2)

Ensure the dust extraction attachment is correctly

attached to the rotary hammer. Using the dust extraction

attachment reduces the risks posed by dust.

– GDE 18V-26 D with GBH 2-26 (F) or GBH 2-28 (F):

Fit the stabilising bracket(11) on the dust extraction at-

tachment.

– Remove the auxiliary handle of the rotary hammer.

– Place the dust extraction attachment on a stable surface.

– Put the front part of the rotary hammer down on the

mounting bracket(9).

– Push the rotary hammer forwards into the clamping

ring(8), until you can hear the rotary hammer click into

place into both of the guide pins(10) and the locking

receptacle(6).

Make sure that the clamping ring(8) of the auxiliary

handle slots into the corresponding groove of the housing

on the rotary hammer.

– Fit the lower gripping end of the auxiliary handle(7).

– Swivel the auxiliary handle(7) around the axis of the

rotary hammer to the required position.

– Turn the lower gripping end of the auxiliary handle(7)

clockwise to tighten it.

– To loosen the rotary hammer from the dust extraction at-

tachment, loosen the clamping ring (8) by turning the

lower gripping end of the auxiliary handle (7) anticlock-

wise.

– Push the locking tab (5) while pulling the rotary hammer

to the rear and pushing downwards at the same time.

Operation

Working advice

uNever use the dust extraction attachment without a

filter. If the dust extraction attachment is used without a

filter, larger particles of drilling dust can be flung towards

the user and the power tool can be damaged.

uDo not use damaged filters (e.g. no cracks, small

holes, etc.). Replace any damaged filters immedi-

ately.

uNever carry the power tool by the dust extraction at-

tachment.

Note: The guide(18) is spring-loaded. The guide can spring

forward when the button(17) for drill bit length adjustment

is pressed.

Switching On and Off

– To switch on the dust extraction attachment, press the

on/off switch(14).

– To switch off the dust extraction attachment, press the

on/off switch(14) again.

Inserting/removing the drill bit (seefigureC)

– Press the button (17) for drilling depth adjustment and

pull the guide (18) all the way out.

– Release the button (17) again.

– Slide the tip of the drill bit through the dust cap (3) from

behind and then fit the bit into the drill chuck according to

the instructions of your power tool.

– Before removing the drill bit, press the button (17) again

and pull the guide (18) all the way out.

Adjusting the Guide Length (seefigureD)

To ensure that dust is extracted cleanly and the depth stop is

set correctly, the guide(18) must be adjusted so that the tip

of the drill bit is flush at the front with the dust cap(1)/(3).

– Insert the required drill bit into the

tool holder of the drill chuck.

– Press the button(17) while adjust-

ing the guide(18) to match the drill

bit length.

– Release the button(17) again.

Note: To store the dust extraction attachment, press the

button(17) and pull the guide(18) all the way out. This re-

lieves the strain on the guide's spring, which increases the

service life of the spring.

Adjusting the Drilling Depth (see figure E)

The button (19) for depth stop adjustment can be used to

set the required drilling depthX.

– Press the button (19) and slide the button on the guide

(18) so that the distance X shown in the illustration

matches your required drilling depth.

– Release the button (19) again.

Fitting the Dust Cap and Extension (seefigureF)

You will need to change the dust cap(1)/(3) depending on

which drill chuck you are using:

– Dust cap(1) for SDS plus quick-change chuck for drilling

diameters of 4–16mm

– Dust cap(2) for SDS plus quick-change chuck for drilling

diameters of 16–26mm

– Dust cap(3) for SDS plus fixed chuck for drilling diamet-

ers of 4–16mm

Bosch Power Tools 1 609 92A 7YA | (11.07.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDE 18V-26 D Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info