Bedienungsanleitung Bosch GDS 18V-210 C (Seite 18 von 279) (Alle Sprachen)

786141

Zoom out

Zoom in

Vorherige Seite

1/279

Nächste Seite

18 | English

Cordless Impact Wrench GDR 18V-210 C GDX 18V-210 C GDS 18V-210 C

Data transfer

Bluetooth®C) Bluetooth® 4.1

(Low Energy)

Bluetooth® 4.1

(Low Energy)

Bluetooth® 4.1

(Low Energy)

Signal interval s 8 8 8

Max. signal rangeD) m 30 30 30

A) Measured at 20–25°C with rechargeable battery ProCORE18V 8.0Ah

B) Measured withGBA 18V 1.5Ah and GBA 18V 12 Ah.

C) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.1) and support the Generic Access Profile

(GAP).

D) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-

ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).

Noise/vibration information

GDR 18V-210 C / GDX 18V-210 C:

Noise emission values determined according to

EN62841-2-2.

Typically, the A-weighted noise level of the power tool is:

Sound pressure level 96dB(A); sound power level

107dB(A). Uncertainty K=3dB.

Wear hearing protection!

GDS 18V-210 C:

Noise emission values determined according to

EN62841-2-2.

Typically, the A-weighted noise level of the power tool is:

Sound pressure level 97dB(A); sound power level

108dB(A). Uncertainty K=3dB.

Wear hearing protection!

Vibration total values ah (triax vector sum) and uncertainty

K determined according to EN62841-2-2:

Impact tightening of fasteners of the maximum capacity of

the tool:

GDR 18V-210 C: ah=10 m/s2, K=1.5 m/s2

GDX 18V-210 C: ah=9 m/s2, K=1.5 m/s2

GDS 18V-210 C: ah=12.5 m/s2, K=1.5 m/s2

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Charging the Battery

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the Battery

The battery (4) is equipped with two locking levels to pre-

vent the battery from falling out when pushing the battery re-

lease button (5) unintentionally. As long as the battery is in-

serted in the power tool, it is held in position by means of a

spring.

To remove the battery (4), press the release button (5) and

pull the battery out of the power tool. Do not use force to

do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the

state of charge of the battery. For safety reasons, it is only

1 609 92A 7X4 | (15.08.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GDS 18V-210 C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info