Bedienungsanleitung Bosch GEF 7 E Professional (Seite 13 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592532

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

English | 13

Bosch Power Tools 1 609 92A 0Y0 | (28.7.14)

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with all rele-

vant provisions of the directives 2011/65/EU, 2014/30/EU,

2006/42/EC including their amendments and complies with

the following standards: EN 60745-1, EN 60745-2-4.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 14.07.2014

Assembly

 Before any work on the machine itself, pull the mains

plug.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Mounting the Auxiliary Handle (see figure A)

 Operate your machine only with the auxiliary handle 3.

Screw the auxiliary handle 3 on the right or left of the machine

head depending on the working method.

Adjusting the Sanding Attachment (see figure B)

– Before adjusting the sanding attachment 10, completely

release clamping lever 5.

– Move the sanding attachment 10 accordingly to suit your

working conditions and working position.

– Close the clamping lever 5 and tighten it firmly.

Note: Clamping lever 5 is indexed (adjustable), allowing it to

be set to an ergonomically favourable or space-saving posi-

tion.

With the clamping lever 5 tightened, pull its lever away from

the machine head, turn it to the desired position and allow it

to engage again.

Changing the Sanding Belt (see figure C)

– Loosen fastening screw 9 and remove the attachment cov-

er 8.

– Press sanding attachment 10 via the supporting surface

14 against a sturdy object (e. g. a bench top) until the

sanding attachment 10 deflects. Remove the sanding belt

12.

– Firstly, position the new sanding belt 12 around on the

drive roller 7 and then around the deflection roller 13. Pay

attention that the arrow directions on the inside of the

sanding belt (if given) and on the attachment cover 8 of the

power tool correspond. Release the sanding attachment

10 again, so that the sanding belt 12 is tensioned.

– Mount the attachment cover 8 with fastening screw 9.

– Adjust the belt run as required, see section “Adjusting the

Belt Run”.

Adjusting the Belt Run (see figure D)

 Adjust the belt run only when the power tool is

switched off and disconnected from the power supply.

Turn adjustment screw 1 until the sanding belt 12 is posi-

tioned centred on deflection roller 13.

Selecting the Sanding Belt

Depending on the material to be worked and the required rate

of removal, different sanding belts are available:

Note: Depending on the application method and the material

being worked, either flexible of stiff sanding belts can be

used.

Changing the Sanding Arm (see figure E)

– Remove the sanding belt 12 (see section “Changing the

Sanding Belt”).

– Unscrew adjustment screw 1 and remove the sanding arm

16.

– Mount the new sanding arm 16 and fasten it with adjust-

ment screw 1.

– Pay attention that the sanding arm 16 is correctly mounted

according to figure E.

– Mount the sanding belt 12 (see section “Changing the

Sanding Belt”).

– Adjust the belt run (see section “Adjusting the Belt Run”).

Operation

Starting Operation

 Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

Grain size

For dry sanding and pre-sanding coarse 40, 60

For structuring and for smoothing

out minor unevenness medium 80, 120

For fine structuring fine

180

Fleece belts

Polishing Fleece belts

OBJ_BUCH-1841-003.book Page 13 Monday, July 28, 2014 1:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GEF 7 E Professional Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info