Bedienungsanleitung Bosch GHO 15-82 Professional (Seite 13 von 164) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

593157

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

English | 13

Bosch Power Tools 1 609 92A 11E | (1.12.14)

18 Scale for rebating width

19 Locking nut for adjustment of rebating width

20 Fastening bolt for parallel and beveling guide

21 Angle stop*

22 Locking nut for angle adjustment

23 Fastening bolt for rebating depth stop

24 Rebating depth stop*

*Accessories shown or described are not part of the standard de-

livery scope of the product. A complete overview of accessories

can be found in our accessories program.

Technical Data

Noise/Vibration Information

Sound emission values determined according to

EN 60745-2-14.

Typically the A-weighted noise levels of the product are:

Sound pressure level 84 dB(A); Sound power level 95 dB(A).

Uncertainty K=3 dB.

Wear hearing protection!

Vibration total values a

(triax vector sum) and uncertainty K

determined according to EN 60745:

=8m/s

, K=1.5 m/s

The vibration level given in this information sheet has been

measured in accordance with a standardised test given in

EN 60745 and may be used to compare one tool with anoth-

er. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main ap-

plications of the tool. However if the tool is used for different

applications, with different accessories or insertion tools or is

poorly maintained, the vibration emission may differ. This

may significantly increase the exposure level over the total

working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may sig-

nificantly reduce the exposure level over the total working

period.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work pat-

terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with all rele-

vant provisions of the directives 2011/65/EU, 2014/30/EU,

2006/42/EC including their amendments and complies with

the following standards: EN 60745-1, EN 60745-2-14.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division

70764 Leinfelden-Echterdingen, GERMANY

Leinfelden, 01.12.2014

Assembly

 Before any work on the machine itself, pull the mains

plug.

Changing the Tool

 Be cautious when replacing the planer blades. Do not

grasp the planer blades by the cutting edges. Possible

danger of injury due to the sharp cutting edges of the plan-

er blades.

Use only original Bosch carbide blades (TC).

The carbide blade (TC) has 2 cutting edges and can be re-

versed. When both cutting edges are dull, the planer blade 12

must be replaced. The carbide blade (TC) may not be resharp-

ened.

Disassembling the Planer Blade(s) (see figure A)

To reverse or replace the planer blade 12, rotate the blade

drum 9 until it is parallel to the planer base plate 6.

Assembling the Planer Blade(s) (see figure B)

The guide groove of the planer blade always ensures continu-

ous height adjustment when replacing or reversing it.

If required, clean the blade seat in the clamping element 10

and the planer blade 12.

When assembling the planer blade, ensure that it is seated

properly in the blade holder of the clamping element 10. The

planer blade must be assembled and aligned centred to the

planer base plate 6. Afterwards tighten the 2 fastening

screws 11 with the Hex key 13.

Note: Before restarting, check if the fastening screws 11 are

tightened well. Rotate the blade drum 9 by hand and ensure

that the planer blade does not graze.

Planer GHO 15-82

Article number

3 601 E94 0..

Rated power input

W600

Output power

W340

No-load speed

min

-1

16000

Planing depth

mm 0 – 1.5

Rebating depth

mm 0 –9

Planing width, max.

mm 82

Weight according to

EPTA-Procedure 01/2003

kg 2.5

Protection class

/II

The values given are valid for a nominal voltage [U] of 230 V. For differ-

ent voltages and models for specific countries, these values can vary.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

 Loosen the two fastening screws 11 with the Hex key 13 by

approx. 1–2turns.

 If necessary, loosen the clamping element 10 by giving it a

light blow with a suitable tool (e.g. a wooden wedge).

 Push the planer blade 12 sidewards out of the blade drum

9 with a piece of wood.

OBJ_BUCH-865-006.book Page 13 Monday, December 1, 2014 7:58 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GHO 15-82 Professional Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info