Bedienungsanleitung Bosch GKS 10.8 V-LI (Seite 18 von 245) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544105

Zoom out

Zoom in

Vorherige Seite

1/245

Nächste Seite

18 | English

1 619 P11 365 | (8.10.13) Bosch Power Tools

Selecting a Saw Blade

An overview of recommended saw blades can be found at the

end of this manual.

Removal of the Saw Blade (see figure A)

For changing the cutting tool, it is best to place the machine

on the face side of the motor housing.

– Press the spindle lock button 6 and keep it pressed.

 The spindle lock button 6 may be actuated only when

the saw spindle is at a standstill. Otherwise, the power

tool can be damaged.

– With the Allen key 5, unscrew the clamping bolt 25 turning

in rotation direction .

– Tilt back the retracting blade guard 21 and hold firmly.

– Remove the clamping flange 24 and the saw blade 23 from

the saw spindle 20.

Mounting the Saw Blade (see figure A)

For changing the cutting tool, it is best to place the machine

on the face side of the motor housing.

– Clean the saw blade 23 and all clamping parts to be assem-

bled.

– Tilt back the retracting blade guard 21 and hold firmly.

– Place the saw blade 23 onto the mounting flange 22. The

cutting direction of the teeth (direction of arrow on the saw

blade) and the direction-of-rotation arrow on the retract-

ing blade guard 21 must correspond.

– Mount the clamping flange 24 and screw in the clamping

bolt 25 turning in rotation direction . Observe correct

mounting position of mounting flange 22 and clamping

flange 24.

– Press the spindle lock button 6 and keep it pressed.

– With the Allen key 5, tighten the clamping bolt 25 turning

in rotation direction . The tightening torque is between

6–9Nm, which corresponds to hand tight plus ¼ turn.

Dust/Chip Extraction

 Before any work on the power tool, remove the battery.

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– To achieve a high level of dust extraction, use a suitable

dust extractor together with this power tool.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Mounting the Extraction Adapter (see figure B)

Fasten the extraction adapter 29 to the base plate 7 with the

fastening screw 28.

A vacuum hose with a diameter of 19 mm can be connected to

the extraction adapter 29.

 The extraction adapter may not be mounted when no

external dust extraction is connected. Otherwise the ex-

traction channel can become clogged.

 Do not connect a dust bag to the extraction adapter.

Otherwise the extraction system can become clogged.

To ensure optimum extraction, the extraction adapter 29

must be cleaned regularly.

External Dust Extraction

Connect the vacuum hose 30 to a vacuum cleaner (accessory).

An overview for connecting to various vacuum cleaners can be

found at the end of this manual.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

Operating Modes

 Before any work on the power tool, remove the battery.

Adjusting the Cutting Depth (see figure C)

 Adjust the cutting depth to the thickness of the work-

piece. Less than a full tooth of the blade teeth should be

visible below the workpiece.

Loosen wing bolt 17. For a smaller cutting depth, pull the ma-

chine from the base plate 7; for a larger cutting depth, push

the machine toward the base plate 7. Adjust the desired cut-

ting depth at the cutting-depth scale 18. Tighten wing bolt 17

again.

When setting the cutting depth, use the reference mark 31 to

the side of the cutting-depth scale 18.

Adjusting the Cutting Angle

It is best to place the machine on the face side of the blade

guard 13.

Loosen wing bolt 10. Tilt the saw sidewards. Adjust the de-

sired setting at the scale 9. Tighten wing bolt 10 again.

When setting the mitre angle, use the reference mark 27 (up-

per edge of the holder).

Note: For bevel cuts, the cutting depth is smaller than the set-

ting indicated on the cutting-depth scale 18.

Cutting Marks

The 0° cutting mark 12 indicates the position of the saw blade

for right-angled cuts. The 45° cutting mark 11 indicates the

position of the saw blade for 45° cuts.

Starting Operation

Inserting the battery

 Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Using

other batteries can lead to injuries and pose a fire hazard.

Insert the charged battery 1 from the front into the base of the

power tool. Push the battery completely into the base until

the red stripe can no longer be seen and the battery is secure-

ly locked.

OBJ_BUCH-2006-001.book Page 18 Tuesday, October 8, 2013 10:38 AM

Bosch GKS 10.8 V-LI Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info