Bedienungsanleitung Bosch GLL 3-80 C (Seite 21 von 317) (Alle Sprachen)

786291

Zoom out

Zoom in

Vorherige Seite

1/317

Nächste Seite

English | 21

Immediately replace a faulty rechargeable battery or any

empty batteries.

Changing the Coin Cell (seefigureA)

The measuring tool is fitted with a coin cell(21) so that date

and time can be saved for theCAL guard function without

having a battery pack or batteries inserted.

In order to change the coin cell, remove the battery pack or

the entire battery adapter.

Pull the button cell holder(22) out of the button cell

port(23). Remove the empty button cell(21) and insert a

new button cell. Ensure that the polarity is correct according

to the illustration on the button cell holder (the positive ter-

minal of the button cell must be facing upwards).

With the button cell fitted, slide the button cell holder(22)

into the port(23). Ensure that the button cell holder is inser-

ted correctly and fully, as otherwise protection from dust

and splashes is no longer guaranteed.

For initial start up, remove the protective film from the but-

ton cell(21). To do this, follow the same steps as when

changing the button cell.

Operation

Starting Operation

uProtect the measuring tool from moisture and direct

sunlight.

uDo not expose the measuring tool to any extreme tem-

peratures or fluctuations in temperature. For example,

do not leave it in a car for extended periods of time. If it

has been subjected to significant fluctuations in temper-

ature, first allow the measuring tool to adjust to the ambi-

ent temperature and then always carry out an accuracy

check before continuing work (see "Accuracy Check of

the Measuring Tool", page23).

The precision of the measuring tool may be compromised

if exposed to extreme temperatures or fluctuations in

temperature.

uAvoid substantial knocks to the measuring tool and

avoid dropping it. Always carry out an accuracy check

before continuing work if the measuring tool has been

subjected to severe external influences (see "Accuracy

Check of the Measuring Tool", page23).

uSwitch the measuring tool off when transporting it.

The pendulum unit is locked when the tool is switched off,

as it can otherwise be damaged by big movements.

Switching On/Off

To switch on the measuring tool, slide the on/off

switch(16) to the " On" position (for working with the pen-

dulum lock) or to the " On"position (for working with

automatic levelling). As soon as it is switched on, the meas-

uring tool emits laser lines from the outlet apertures(1).

uDo not direct the laser beam at persons or animals and

do not stare into the laser beam yourself (even from a

distance).

To switch off the measuring tool, slide the on/off switch

(16) to the Off position. The pendulum unit is locked when

the tool is switched off.

uNever leave the measuring tool unattended when

switched on, and ensure the measuring tool is

switched off after use. Others may be blinded by the

laser beam.

If the maximum permitted operating temperature of 40 °C is

exceeded, the tool shuts down to protect the laser diode.

Once it has cooled down, the measuring tool is operational

again and can be switched back on.

If the temperature of the measuring tool is approaching the

maximum permissible operating temperature, the laser lines

will gradually become dimmer.

The measuring tool is protected against electrostatic dis-

charge (ESD). If the measuring tool becomes electrostatic-

ally charged (e.g. when it is touched in an environment with

low humidity), it switches itself off automatically. In such

cases, switch the on/off switch(16) off and on again.

Deactivating the Automatic Shut-Off Function

If no button on the measuring tool is pressed for approx.

120min, the measuring tool will automatically switch itself

off to preserve battery life.

To switch the measuring tool back on after it has been auto-

matically switched off, you can either slide the on/off switch

(16) to the "Off" position first and then switch the measur-

ing tool back on, or press either the laser mode button (7) or

the receiver mode button (5) once.

To deactivate the automatic shut-off function, hold down the

laser mode button (7) for at least 3s (with the measuring

tool switched on). If the automatic shut-off function is deac-

tivated, the laser beams will flash briefly as confirmation.

To activate the automatic shut-off function, switch the meas-

uring tool off and on again.

Deactivating the Signal Tone Function

The signal tone function is always activated once the meas-

uring tool is switched on.

To deactivate or activate the signal tone function, simultan-

eously press the laser mode button (7) and the receiver

mode button (5) and hold them down for at least 3s.

Three short signal tones will sound as confirmation both

when the signal tone function is activated and deactivated.

Operating Modes

The measuring tool has several operating modes which you

can switch between at any time. These are for:

– Generating a horizontal laser plane,

– Generating a vertical laser plane,

– Generating two vertical laser planes,

– Generating a horizontal laser plane and two vertical laser

planes.

After you switch it on, the measuring tool generates a hori-

zontal laser plane. To change the operating mode, press the

laser mode button (7).

Bosch Power Tools 1 609 92A 7GY | (21.04.2022)

Bosch GLL 3-80 C Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info