Bedienungsanleitung Bosch GLL 3-80 C (Seite 22 von 317) (Alle Sprachen)

786291

Zoom out

Zoom in

Vorherige Seite

1/317

Nächste Seite

22 | English

All operating modes can be selected with both automatic lev-

elling or the pendulum lock.

Receiver Mode

Receiver mode must be activated when working with the

laser receiver (29), regardless of which operating mode is

selected.

In receiver mode, the laser lines flash at a very high fre-

quency, enabling them to be detected by the laser receiver

(29).

To switch on receiver mode, press the receiver mode button

(5). The receiver mode indicator (6) will light up green.

When receiver mode is switched on, the laser lines are less

visible to the human eye. Therefore, switch receiver mode

off by pressing the receiver mode button (5) again to work

without a laser receiver. The receiver mode indicator (6) will

go out.

Automatic Levelling

Working with Automatic Levelling

Position the measuring tool on a level, firm surface or attach

it to the universal holder(25) or the tripod(32).

For work with automatic levelling, slide the on/off

switch(16) to the " On" position.

The automatic levelling function automatically compensates

irregularities within the self-levelling range of ±4°. The level-

ling is finished as soon as the laser lines stop moving.

If automatic levelling is not possible, e.g. because the sur-

face on which the measuring tool stands deviates by more

than4° from the horizontal plane, the laser lines will begin to

flash quickly. If the signal tone function is activated, rapid

signal tones will sound.

Place the measuring tool in a horizontal position and wait for

self-levelling to take place. As soon as the measuring tool is

within the self-levelling range of ±4°, the laser beams will

light up continuously and the signal tones will cease.

In case of ground vibrations or position changes during oper-

ation, the measuring tool is automatically levelled again.

Upon re-levelling, check the position of the horizontal or ver-

tical laser line with regard to the reference points to avoid er-

rors by moving the measuring tool.

Working with the Pendulum Lock

For work with the pendulum lock, slide the on/off

switch(16) to the " On" position. The pendulum lock

indicator(4) lights up red and the laser lines continuously

flash slowly.

For work with the pendulum lock, the automatic levelling is

switched off. You can hold the measuring tool freely in your

hand or place it on a sloping surface. This means that the

laser lines are no longer levelled and no longer necessarily

run perpendicular to one another.

Remote control via the Bosch Levelling Remote

App

The measuring tool is equipped with a Bluetooth® module

which uses radio technology to enable remote control via a

smartphone with a Bluetooth® interface.

The Bosch Levelling Remote App application (app) is re-

quired to use this function. You can download this in the app

store for your terminal device (Apple App Store, Google Play

Store).

Information about the system requirements for a Bluetooth®

connection can be found on the Bosch website at

www.bosch‑pt.com

When remote controlling via Bluetooth®, poor reception con-

ditions can cause time delays between the mobile terminal

device and the measuring tool.

Switching on Bluetooth®

To switch on Bluetooth®, press the Bluetooth® button(9).

Ensure that the Bluetooth® interface is activated on your mo-

bile terminal device.

The connection between mobile end device and measuring

tool is established after the Bosch application has started. If

multiple active measuring tools are found, select the appro-

priate measuring tool. A connection will be established auto-

matically if only one active measuring tool is found.

The connection is established as soon as the Bluetooth® in-

dicator (8) lights up.

The Bluetooth® connection may be interrupted if the dis-

tance between the measuring tool and the mobile terminal

device is too great or is blocked, and if there are any sources

of electromagnetic interference. Should this occur, the

Bluetooth® indicator (8) will flash.

Switching off Bluetooth®

To switch off Bluetooth® for remote control, press the

Bluetooth® button (9) or switch off the measuring tool.

Calibration warning CAL guard

The sensors for calibration warning CAL guard monitor the

status of the measuring tool, even when it is switched off. If

the measuring tool is not being supplied with power by a re-

chargeable battery or non-rechargeable batteries, an in-

ternal energy storage system provides continuous monitor-

ing by the sensors for 72 hours.

The sensors are activated when the measuring tool is started

up for the first time.

Calibration Warning Triggers

If one of the following events occurs, the calibration warning

CAL guard is triggered and the indicator CAL guard(3)

lights up red:

– The calibration interval (every 12 months) has expired.

– The measuring tool was stored outside of the storage

temperature range.

– The measuring tool was subjected to a strong shock (e.g.

impact with the ground after being dropped).

You can refer to the Bosch Levelling Remote App to see

which of the three events triggered the calibration warning.

1 609 92A 7GY | (21.04.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GLL 3-80 C Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info