Bedienungsanleitung Bosch GOP 10.8 V-LI Professional (Seite 18 von 234) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591822

Zoom out

Zoom in

Vorherige Seite

1/234

Nächste Seite

18 | English

1 609 92A 116 | (31.3.15) Bosch Power Tools

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Connecting the Dust Extraction (see figure A)

For sanding, always connect the dust extraction.

Remove the application tool/accessory when mounting the

dust extraction 19 (accessory).

If required, assemble the parts of the dust extraction 19 as

shown in the figure. Position the assembled dust extraction

onto the machine via the tool holder 8. Turn the dust extrac-

tion in such a manner that the cams of the dust extraction en-

gage into the corresponding recesses on the housing. Fasten

the dust extraction to the machine with the retaining clip 17

as shown in the figure.

Pay attention that the felt ring 16 is undamaged and faces

tightly against the sanding plate 14. Replace a damage felt

ring immediately.

Depending on machine version, place a vacuum hose 20 (ac-

cessory) either directly onto the vacuum connection 18 or cut

off the old hose end, screw the extraction adapter 21 (acces-

sory) onto the hose end and then place it directly onto the

vacuum connection 18. Connect the vacuum hose 20 with a

vacuum cleaner (accessory). An overview for the connection

of various vacuum cleaners can be found on the fold-out page.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium-ion batteries with the

voltage listed on the nameplate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

Insert the charged battery 2 into the handle until it can be felt

to engage and faces flush against the handle.

Switching On and Off

To start the machine, push the On/Off switch 7 forward so

that the “I” is indicated on the switch.

To switch off the machine, push the On/Off switch 7 toward

the rear so that the “0” is indicated on the switch.

To save energy, only switch the power tool on when using it.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Note: If the machine should automatically switch off because

of a discharged or overheated battery, make sure to set the

machine’s On/Off switch 7 to off. Charge the battery and al-

low it to cool down before restarting the machine. Otherwise

the battery can become damaged.

Preselecting the Orbital Stroke Rate

With the thumbwheel for preselection of the orbital stroke

rate 5, you can preselect the required orbital stroke rate, even

during operation.

The required stroke rate depends on the material and the

working conditions and can be determined through practical

testing.

Working Advice

 Before any work on the machine itself (e.g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Wait until the machine has come to a standstill before

placing it down.

Note: Do not cover off the venting slots 6 of the machine while

working, as this reduces the working life of the machine.

Operating Principle

Due to the oscillating drive the application tool/accessory

oscillates up to 20000 times per minute at 2.8°. This allows

for precise work in narrow spaces.

Work with low and uniform application

pressure, otherwise, the working perfor-

mance will decline and the application tool

can become blocked.

While working, move the machine back and

forth, so that the application tool does not

heat up excessively and become blocked.

Sawing

 Use only undamaged saw blades that are in perfect con-

dition. Bent or dull saw blades can break, negatively influ-

ence the cut, or lead to kickback.

 When sawing light building materials, observe the stat-

utory provisions and the recommendations of the ma-

terial suppliers.

 Plunge cuts may only be applied to soft materials, such

as wood, gypsum plaster boards, etc.!

Before sawing with HCS saw blades in wood, particle board,

building materials, etc., check these for foreign objects such

as nails, screws, or similar. If required, remove foreign ob-

jects or use BIM saw blades.

Separating

Note: When separating wall tiles take into consideration that

the application tools/accessories wear heavily when used for

longer periods of time.

OBJ_BUCH-630-008.book Page 18 Tuesday, March 31, 2015 6:05 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 10.8 V-LI Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info