Bedienungsanleitung Bosch GOP 18 V-EC (Seite 16 von 213) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544108

Zoom out

Zoom in

Vorherige Seite

1/213

Nächste Seite

16 | English

2 609 140 973 | (31.5.13) Bosch Power Tools

Removing the battery

The battery 5 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 3 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

To remove the battery 5, press the battery unlocking button 3

and pull the battery out of the power tool toward the rear. Do

not exert any force.

Battery Charge-control Indication

The three green LEDs of the battery charge-control indicator

6 indicate the charge condition of the battery 5. For safety

reasons, it is only possible to check the status of the charge

condition when the machine is at a standstill.

Press button 7 to indicate the charge condition. This is also

possible when the battery 5 is removed.

When no LED lights up after pushing button 7, then the bat-

tery is defective and must be replaced.

Changing the Tool

 Before any work on the machine itself (e.g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 Wear protective gloves when changing application

tools/accessories. Contact with the application tool/ac-

cessoriy can lead to injuries.

Selecting the Application Tool/Accessory

Mounting/Replacing the Application Tool/Accessory

If required, remove an already mounted application tool/

accessory.

For this, open the SDS lever 8 to the stop (not further) and

remove the application tool.

Mount the requested application tool/accessory (e.g. plunge

cut saw blade 11) in such a manner on the tool holder 9 that

the offset faces downward (see illustration on the graphics

page; marking on the application tool/accessory is readable

from above).

Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 9. 12 different positions are possible, each

offset by 30°.

Close SDS lever 8 so that it faces against the housing of the

power tool.

 Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting/Replacing a Sanding Sheet on the Sanding Plate

The sanding plate 12 is fitted with Velcro backing for quick

and easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 13, free the Velcro back-

ing of the sanding plate 12 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 13 flush alongside one edge of the

sanding plate 12, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

LED Capacity

Continuous lighting 3 x green  2/3

Continuous lighting 2 x green  1/3

Continuous lighting 1 x green <1/3

Flashing light 1 x green Reserve

Accessory Material

HCS wood seg-

ment saw blade*

Wooden materials,

plastic

BIM segment saw

blade*

Wooden materials,

plastic, non-ferrous

metals

HCS plunge cut

saw blades,

wood*

Wooden materials,

plastic, gypsum and

other soft materials

BIM plunge cut

saw blades,

metal*

Metal (e.g. unhard-

ened nails, screws,

smaller profiles),

non-ferrous metals

BIM plunge cut

saw blade, wood

and metal*

Wood, metal, non-

ferrous metals

* Optional accessory; for the complete accessories please see Bosch

accessory programme.

HM-Riff segment

saw blade*

Grouting joints, soft

wall tiles, glass-fibre

reinforces plastic

and other abrasive

materials

HM-Riff delta

plate*

Scraper, rigid* Carpets, coverings

Scraper, flexible* Silicone and other

elastic materials

Base plate for

sanding, series

Delta 93 mm*

Depends on sanding

sheet

Accessory Material

* Optional accessory; for the complete accessories please see Bosch

accessory programme.

OBJ_BUCH-1808-001.book Page 16 Friday, May 31, 2013 9:29 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 18 V-EC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info