Bedienungsanleitung Bosch GOP 18 V-EC (Seite 17 von 213) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544108

Zoom out

Zoom in

Vorherige Seite

1/213

Nächste Seite

English | 17

Bosch Power Tools 2 609 140 973 | (31.5.13)

To remove the sanding sheet 13, grasp it at one of the tips and

pull it off from the sanding plate 12.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Connecting the Dust Extraction (see figure A)

For sanding, always connect the dust extraction.

Remove the application tool/accessory when mounting the

dust extraction 17 (accessory).

If required, assemble the parts of the dust extraction 17 as

shown in the figure. Position the assembled dust extraction

onto the machine via the tool holder 9. Turn the dust extrac-

tion in such a manner that the cams of the dust extraction en-

gage into the corresponding recesses on the housing. Fasten

the dust extraction to the machine with the retaining clip 15

as shown in the figure.

Pay attention that the felt ring 14 is undamaged and faces

tightly against the sanding plate 12. Replace a damage felt

ring immediately.

Depending on the machine model, place a vacuum hose 18

(accessory) either directly onto the vacuum connection 16 or

cut off the old hose end, screw the extraction adapter 19 (ac-

cessory) onto the hose end and insert it directly into the vac-

uum connection 16. Connect the vacuum hose 18 with a vac-

uum cleaner (accessory). An overview for the connection of

various vacuum cleaners can be found at the end of these in-

structions.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Using

other batteries can lead to injuries and pose a fire hazard.

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

Insert the charged battery pack 5 from the rear into the base

of the power tool. Press the battery pack completely into the

base until the red stripe can no longer be seen and the battery

pack is securely locked.

Sanding disc Material Application Grain size

– All wooden materials

(e.g., hardwood, soft-

wood, chipboard, build-

ing board)

– Metal materials

For coarse-sanding, e.g. of rough, unplaned beams and

boards

coarse 40

For face sanding and planing small irregularities

medium 80

100

120

For finish and fine sanding of wood

fine 180

240

320

400

–Paint

–Varnish

– Filling compound

–Filler

For sanding off paint

coarse 40

For sanding primer (e.g., for removing brush dashes, drops

of paint and paint run)

medium 80

100

120

For final sanding of primers before coating

fine 180

240

320

400

OBJ_BUCH-1808-001.book Page 17 Friday, May 31, 2013 9:29 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 18 V-EC Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info