Bedienungsanleitung Bosch GOP 250 CE Professional (Seite 16 von 217) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

593438

Zoom out

Zoom in

Vorherige Seite

1/217

Nächste Seite

16 | English

2 609 932 934 | (8.10.14) Bosch Power Tools

Selecting the Application Tool/Accessory

Mounting/Replacing the Application Tool/Accessory

(GOP 250 CE)

If required, remove an already mounted application tool/ac-

cessory.

For removing the application tool/accessory, loosen the

screw 7 with the hex key 8 and remove the application

tool/accessory.

Mount the requested application tool/accessory (e.g. plunge

cut saw blade 6) in such a manner on the tool holder 4 that the

offset faces downward (see illustration on the graphics page;

marking on the application tool/accessory is readable from

above).

Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 4. 12 different positions are possible, each

offset by 30°.

For more intermediate positions, the adapter 9 (accessory)

can be used: Allow the adapter to engage with the smooth

side onto the cams of the tool holder 4 (see illustration on the

graphics page). Position the application tool/accessory onto

the adapter in any position.

Fasten the application tool/accessory with bolt 7. Tighten the

bolt with hex key 8 until the spring washer of the bolt faces

flush against the application tool/accessory.

 Check the tight seating of the application tool/accesso-

ry. Incorrect or not securely fastened application tools/ac-

cessories can come loose during operation and pose a haz-

ard.

Mounting/Replacing the Application Tool/Accessory

(GOP 300 SCE)

If required, remove an already mounted application tool/

accessory.

For this, open the SDS lever 12 to the stop (not further) and

remove the application tool.

Mount the requested application tool/accessory (e.g. plunge

cut saw blade 6) in such a manner on the tool holder 4 that the

offset faces downward (see illustration on the graphics page;

marking on the application tool/accessory is readable from

above).

Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 4. 12 different positions are possible, each

offset by 30°.

Close SDS lever 12 so that it faces against the housing of the

power tool.

 Check the tight seating of the application tool/accesso-

ry. Incorrect or not securely fastened application tools/ac-

cessories can come loose during operation and pose a haz-

ard.

Mounting/Replacing a Sanding Sheet on the Sanding

Plate

The sanding plate 10 is fitted with Velcro backing for quick

and easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 11, free the Velcro back-

ing of the sanding plate 10 from any debris by tapping against

it in order to enable optimum adhesion.

Position the sanding sheet 11 flush alongside one edge of the

sanding plate 10

, then lay the sanding sheet onto the sanding

plate and press firmly.

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

To remove the sanding sheet 11, grasp it at one of the tips and

pull it off from the sanding plate 10.

You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Accessory Material

HCS wood seg-

ment saw blade*

Wooden materials,

plastic

BIM segment saw

blade*

Wooden materials,

plastic, non-ferrous

metals

HCS plunge cut

saw blades,

wood*

Wooden materials,

plastic, gypsum and

other soft materials

BIM plunge cut

saw blades,

metal*

Metal (e. g. unhard-

ened nails, screws,

smaller profiles),

non-ferrous metals

BIM plunge cut

saw blade, wood

and metal*

Wood, metal, non-

ferrous metals

HM-Riff segment

saw blade*

Grouting joints, soft

wall tiles, glass-fibre

reinforces plastic

and other abrasive

materials

HM-Riff delta

plate*

Scraper, rigid* Carpets, coverings

Scraper, flexible* Silicone and other

elastic materials

Base plate for

sanding, series

Delta 93 mm*

Depends on sanding

sheet

* Optional accessory; for the complete accessories please see Bosch

accessory programme.

OBJ_BUCH-1271-005.book Page 16 Wednesday, October 8, 2014 11:11 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 250 CE Professional Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info