Bedienungsanleitung Bosch GOP 250 CE Professional (Seite 18 von 217) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

593438

Zoom out

Zoom in

Vorherige Seite

1/217

Nächste Seite

18 | English

2 609 932 934 | (8.10.14) Bosch Power Tools

The required stroke rate depends on the material and the

working conditions and can be determined through practical

testing.

Working Advice

 Before any work on the machine itself, pull the mains

plug.

 Wait until the machine has come to a standstill before

placing it down.

Note: Do not cover off the venting slots 3 of the machine while

working, as this reduces the working life of the machine.

Operating Principle

Due to the oscillating drive the application tool/accessory

oscillates up to 20000 times per minute at 2.8°. This allows

for precise work in narrow spaces.

Work with low and uniform application

pressure, otherwise, the working perfor-

mance will decline and the application tool

can become blocked.

While working, move the machine back and

forth, so that the application tool does not

heat up excessively and become blocked.

Sawing

 Use only undamaged saw blades that are in perfect con-

dition. Bent or dull saw blades can break, negatively influ-

ence the cut, or lead to kickback.

 When sawing light building materials, observe the stat-

utory provisions and the recommendations of the ma-

terial suppliers.

 Plunge cuts may only be applied to soft materials, such

as wood, gypsum plaster boards, etc.!

Before sawing with HCS saw blades in wood, particle board,

building materials, etc., check these for foreign objects such

as nails, screws, or similar. If required, remove foreign ob-

jects or use BIM saw blades.

Separating

Note: When separating wall tiles take into consideration that

the application tools/accessories wear heavily when used for

longer periods of time.

Sanding

The removal rate and the sanding pattern are primarily deter-

mined by the choice of sanding sheet, the preset oscillation

rate and the applied pressure.

Only flawless sanding sheets achieve good sanding capacity

and extend the service life of the machine.

Pay attention to apply uniform sanding pressure; this increas-

es the working life of the sanding sheets.

Intensifiying the sanding pressure does not lead to an in-

crease of the sanding capacity, but to increased wear of the

machine and the sanding sheet.

For precise on-the-spot sanding of edges, corners and hard to

reach areas, it is also possible to work only with the tip or an

edge of the sanding plate.

When selectively sanding on the spot, the sanding sheet can

heat up considerably. Reduce the orbital stroke rate and the

sanding pressure, and allow the sanding sheet to cool down

regularly.

A sanding sheet that has been used for metal should not be

used for other materials.

Use only original Bosch sanding accessories.

For sanding, always connect the dust extraction.

Scraping

For scraping, select a high oscillation rate.

Work on a soft surface (e.g. wood) at a flat ange, and apply

only light pressure. Otherwise the scraper can cut into the

surface.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains

plug.

 For safe and proper working, always keep the machine

and ventilation slots clean.

Clean Riff application tools (accessory) regularly with a wire

brush.

If the replacement of the supply cord is necessary, this has to

be done by Bosch or an authorized Bosch service agent in or-

der to avoid a safety hazard.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. Exploded views and information on spare parts can al-

so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions

concerning our products and their accessories.

In all correspondence and spare parts order, please always in-

clude the 10-digit article number given on the type plate of

the machine.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange

the collection of a product in need of servicing or repair.

Tel. Service: (0844) 7360109

E-Mail: boschservicecentre@bosch.com

OBJ_BUCH-1271-005.book Page 18 Wednesday, October 8, 2014 11:11 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GOP 250 CE Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info