Bedienungsanleitung Bosch GRO 10.8 V-LI (Seite 16 von 238) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544114

Zoom out

Zoom in

Vorherige Seite

1/238

Nächste Seite

16 | English

1 619 P11 460 | (26.11.13) Bosch Power Tools

Safety warnings specific for Grinding and Abrasive Cut-

ting-Off operations

 Use only wheel types that are recommended for your

power tool and only for recommended applications.

For example: do not grind with the side of a cut-off

wheel. Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may cause

them to shatter.

 For threaded abrasive cones and plugs use only undam-

aged wheel mandrels with an unrelieved shoulder

flange that are of correct size and length. Proper man-

drels will reduce the possibility of breakage.

 Do not “jam” the cut-off wheel or apply excessive pres-

sure. Do not attempt to make an excessive depth of cut.

Overstressing the wheel increases the loading and suscep-

tibility to twisting or binding of the wheel in the cut and the

possibility of kickback or wheel breakage.

 Do not position your hand in line with and behind the ro-

tating wheel. When the wheel, at the point of operation, is

moving away from your hand, the possible kickback may

propel the spinning wheel and the power tool directly at you.

 When wheel is pinched, snagged or when interrupting a

cut for any reason, switch off the power tool and hold the

power tool motionless until the wheel comes to a com-

plete stop. Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion otherwise kick-

back may occur. Investigate and take corrective action to

eliminate the cause of wheel pinching or snagging.

 Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

 Support panels or any oversized workpiece to minimize

the risk of wheel pinching and kickback. Large work-

pieces tend to sag under their own weight. Supports must

be placed under the workpiece near the line of cut and near

the edge of the workpiece on both sides of the wheel.

 Use extra caution when making a “pocket cut” into ex-

isting walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects that

can cause kickback.

Safety warnings specific for wire brushing operations

 Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush. The wire

bristles can easily penetrate light clothing and/or skin.

 Allow brushes to run at operating speed for at least one

minute before using them. During this time no one is to

stand in front or in line with the brush. Loose bristles or

wires will be discharged during the run-in time.

 Direct the discharge of the spinning wire brush away

from you. Small particles and tiny wire fragments may be

discharged at high velocity during the use of these brushes

and may become imbedded in your skin.

Additional safety warnings

Wear safety goggles.

 Use appropriate detectors to determine if utility lines

are hidden in the work area or call the local utility compa-

ny for assistance. Contact with electric lines can lead to fire

and electric shock. Damaging a gas line can lead to explo-

sion. Penetrating a water line causes property damage.

 Secure the workpiece. A workpiece clamped with clamp-

ing devices or in a vice is held more secure than by hand.

 The power tool is not suitable for stationary operation.

For example, it may not be clamped in a vice or fastened on

a workbench.

 Do not open the battery. Danger of short-circuiting.

Protect the battery against heat, e. g., against

continuous intense sunlight, fire, water, and mois-

ture. Danger of explosion.

 In case of damage and improper use of the battery, va-

pours may be emitted. Ventilate the area and seek

medical help in case of complaints. The vapours can irri-

tate the respiratory system.

 Use the battery only in conjunction with your Bosch

power tool. This measure alone protects the battery

against dangerous overload.

 The battery can be damaged by pointed objects such as

nails or screwdrivers or by force applied externally. An

internal short circuit can occur and the battery can burn,

smoke, explode or overheat.

Product Description and Specifications

Read all safety warnings and all instruc-

tions. Failure to follow the warnings and in-

structions may result in electric shock, fire

and/or serious injury.

While reading the operating instructions, unfold the graphics

page for the machine and leave it open.

Intended Use

The power tool is intended for cutting metal and stone materi-

als, and for grinding, sanding and polishing metal and painted

surfaces without the use of water. In addition to this, the pow-

er tool is suitable for drilling in wood, soft metal, plastic and

light building materials when used with the appropriate ac-

cessories.

The light of this power tool is intended to illuminate the power

tool’s direct area of working operation and is not suitable for

household room illumination.

OBJ_BUCH-2020-001.book Page 16 Tuesday, November 26, 2013 2:57 PM

Bosch GRO 10.8 V-LI Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info