Bedienungsanleitung Bosch GRO 10.8 V-LI (Seite 18 von 238) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544114

Zoom out

Zoom in

Vorherige Seite

1/238

Nächste Seite

18 | English

1 619 P11 460 | (26.11.13) Bosch Power Tools

Note: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Observe the notes for disposal.

Removing the battery (see figure A)

– To remove the battery 9, press the unlocking buttons 16

and pull the battery out of the machine to the rear. Do not

exert any force.

Battery Charge-control Indication

The three green LEDs of the battery charge-control indicator

8 indicate the charge condition of the battery 9.

Changing the Tool

 When inserting an application tool, pay attention that

the shank of the application tool is firmly seated in the

tool holder. When the shank of the application tool is not

inserted deep enough in the tool holder, the application

tool can become loose again and not be controlled.

 Use only flawless tool bits that are not worn. Defective

tool bits can break, for example, and cause injury or dam-

age.

 Only use brand accessories for grinding, sanding,

brushing, polishing, routing and cut-off grinding from

the dealer for the power tool, which are approved for a

speed of 35000 rpm and which have a shank with an

outside diameter of 3.2 mm.

Inserting (see figure B)

– Press the spindle lock 5 and turn the clamping nut 12 by

hand until locked.

– Press and hold the spindle lock and loosen the clamping

nut 12 with the open-end spanner 17 by turning it in an an-

ticlockwise direction.

– Insert the dust-free application tool (e.g. holding rod 2,

grinding accessory 3 or drill bit) into the collet 13 of the

collet chuck 19.

Note: Ensure that the shank 18 of the application tool sits in

as far as possible, but at least 10 mm into the collet chuck.

– Press and hold the spindle lock 5 and tighten the applica-

tion tool by turning the clamping nut 12 with the open-end

spanner 17 in a clockwise direction.

Removing

– Loosen the clamping nut 12 as previously described and

remove the application tool.

Mounting a Cutting Disc (see figure C)

Cutting discs reinforced with fibreglass are included in the

scope of delivery. They can be used for grooving, routing and

cutting metal, wood and plastic.

– Insert the holding rod 2 into the collet (see “Inserting”,

page 18).

– Press and hold the spindle lock 5 and completely unscrew

the screw on the holding rod 2 using the screwdriver 17.

– Attach the cutting disc 1 to the holding rod 2 and reinsert

and tighten the screw.

Changing the Collet Chuck (see figure D)

– Press the spindle lock 5 and turn the clamping nut 12 by

hand until locked.

– Press and hold the spindle lock and loosen the clamping

nut 12 with the open-end spanner 17 by turning it in an an-

ticlockwise direction.

– Remove the clamping nut 12 together with the collet chuck

19.

– Insert the required collet chuck into the drive spindle 20.

– Screw the clamping nut 12 onto the drive spindle 20 and

tighten it slightly in a clockwise direction using the open-

end spanner 17.

Replacing the Dust Protection Cap (see figure E)

Two dust protection caps are included in the scope of deliv-

ery.

Use the dust protection cap 11 when you need a good grip for

detailed work.

Use the dust protection cap 21 when you have to work close

to the workpiece surface.

The dust protection cap largely prevents the penetration of

dust into the tool holder during operation. When inserting the

tool, pay attention that the dust protection cap is not damaged.

– Unscrew the dust protection cap used.

– Screw on the new dust protection cap and tighten it.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

LED Meaning

Continuous lighting

3 x green

Battery Capacity ≥2/3

Continuous lighting

2 x green

Battery Capacity ≥1/3

Continuous lighting

1 x green

Battery Capacity <1/3

Flashing light 1 x green Reserve

Continuous lighting

1 x red

Power tool has overheated!

– Switch the power tool off and al-

low it to cool down completely.

Flashing light

1 x red

Power tool has overloaded!

– Exert less pressure on the work-

piece during work.

OBJ_BUCH-2020-001.book Page 18 Tuesday, November 26, 2013 2:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GRO 10.8 V-LI Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info