Bedienungsanleitung Bosch GSB 18V-150 C (Seite 21 von 297) (Alle Sprachen)

786163

Zoom out

Zoom in

Vorherige Seite

1/297

Nächste Seite

English | 21

Swivelling the auxiliary handle

You can swivel the auxiliary handle (4) to any angle for a safe

work posture that minimises fatigue.

Turn the lower gripping end of the auxiliary handle (4) anti-

clockwise and swivel the auxiliary handle (4) into the re-

quired position. Afterwards, turn the lower gripping end of

the auxiliary handle (4) clockwise to retighten it.

Setting the drilling depth

You can use the depth stop(3) to set the required drilling

depth X.

Loosen the wing bolt for adjusting the depth stop (5) and in-

sert the depth stop into the auxiliary handle (4).

Pull the depth stop(3) far enough out that the distance

between the drill bit tip and the edge of the depth stop(3)

corresponds to the required drilling depth X.

Retighten the wing bolt for adjusting the depth stop (5).

Changing the tool (see figure A)

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

The drill spindle is locked when the on/off switch (17) is not

pressed. This makes it possible to change the application

tool in the drill chuck quickly, conveniently and easily.

Open the keyless chuck (2) by turning it in the direction of

rotation  until the tool can be inserted. Insert the tool.

Firmly tighten the keyless chuck (2) by turning it by hand in

the direction of rotation . This will automatically lock the

drill chuck.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (16) to the middle posi-

tion to avoid unintentionally switching it on. Insert the

charged battery (11) into the handle until you feel it engage

and it is flush with the handle.

Setting the rotational direction (see figure B)

The rotational direction switch (16) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (17) is being pressed.

Rotate clockwise: Slide the rotational direction

switch (16) on both sides until it stops in the posi-

tion.

Rotate anti-clockwise: Slide the rotational direction

switch (16) on both sides until it stops in the posi-

tion.

Setting the operating mode

Drilling

Set the mode selector switch(7) to the

"drilling" symbol.

Screwdriving

Set the mode selector switch(7) to the "screw-

driving" symbol.

Impact drilling (GSB 18V-150 C)

Set the mode selector switch(7) to the "impact

drilling" symbol.

Switching on/off

To start the power tool, press and hold the on/off switch

(17).

The LED (13) lights up when the on/off switch (17) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (17).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (17) to varying extents.

A light pressure on the on/off switch (17) results in a low ro-

tational speed. Increased pressure on the switch causes an

increase in speed.

Preselecting torque (applies to screwdriving mode)

The torque presetting ring (6) can be used to preselect the

required torque in 25 stages. Once the set torque has been

reached, the application tool will be stopped.

Mechanical gear selection

uOnly operate the gear selector (8) when the power

tool is not in use.

Bosch Power Tools 1 609 92A 838 | (14.07.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSB 18V-150 C Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info