Bedienungsanleitung Bosch GSB 18V-150 C (Seite 22 von 297) (Alle Sprachen)

786163

Zoom out

Zoom in

Vorherige Seite

1/297

Nächste Seite

22 | English

First gear:

Low speed range; for working with a large drilling diameter

or for screwdriving.

Second gear:

High speed range; for working with a small drilling diameter.

uAlways push the gear selector switch as far as it will

go. Otherwise, the power tool may become damaged.

Rapid Shut-off (KickBack Control)

The rapid shut-off function (KickBack Con-

trol) gives the user greater control over the

power tool and offers them better protec-

tion than power tools that do not have Kick-

Back Control. The power tool will switch off if it suddenly

and unforeseeably rotates around the drilling axis.

The rapid shut-off is indicated by the LED(22) flashing red,

a flashing light from the worklight(13) and the LED of the

KickBack Control(23) lighting up red on the power tool.

To switch the tool back on, release the on/off switch and

then press it again.

uIt will no longer be possible to switch the power tool

on if the KickBack Control function is faulty. Have the

power tool serviced by a qualified repair person using

only original replacement parts.

The rapid shut-off function can be deactivated on the user

interface(14) with the button(24). If the power tool is not

used for longer than 5 minutes or if the rechargeable battery

is removed, the rapid shut-off function automatically

switches back on. The current status is shown via the LED

for KickBack Control(23) on the user interface(14).

Please note that the warning light is not visible from all direc-

tions. The warning light is difficult to see in bright sunlight.

Electronic Angle Detection (EAD)

With electronic angle detection (EAD), a slope angle can be

preselected that the power tool detects during work and dis-

plays to the user. This means it is possible to drill or screw at

right angles in a sloped surface, for example. Electronic

angle detection (EAD) is controlled via the user

interface(14).

Select an angle (45°, 60°, user-defined) on the user

interface(14). Note: The user-defined angle in the factory

settings is 90°. This angle can be adjusted via the Bosch app.

To adjust the angle, press the button for the electronic angle

detection (EAD)(20) until the LED of the required slope

angle(21) starts flashing.

In addition to the LED of the required slope angle(21), the

LED of the electronic angle detection (EAD)(9) also starts to

flash yellow. Now position the power tool on the required

surface and hold it as still as possible. Note: If the power tool

is not held still during the initiating process, the initiating

process will automatically end after 10seconds and the last

set value is restored.

The power tool will start the initiating process once it is posi-

tioned. The required surface is taught in during the initiating

process. The initiating process is complete when the LED of

the electronic angle detection (EAD)(9) lights up green for

approx. 1second and then goes out, and the LED of the

slope angle(21) lights up continuously.

Remove the power tool from the surface. Align the power

tool with the taught-in surface in the required slope angle.

The LED(22) lights up yellow if the slope angle lies in the

range +/-10° from the preset slope angle.

If a slope angle within +/–3° of the preset slope angle is

reached, the LED(9) lights up green. To end the electronic

angle detection (EAD), press the button for the electronic

angle detection (EAD)(20) until none of the LEDs for angle

selection(21) are lit up (45°  60°  User-defined  Off).

The set angle and reference surface are saved even when

changing the rechargeable battery or when waking up the

power tool from sleep mode.

User Interface (seefigureD)

The user interface(14) is used to set and check a slope

angle as part of the electronic angle detection (EAD), to de-

activate the rapid shut-off (KickBack Control) and to indicate

the status of the power tool.

Status Indications

Status indicator for

power tool(22) Meaning/cause Solution

Green Status OK –

Yellow Critical temperature has been reached, re-

chargeable battery is almost empty, or KickBack

Control is switched off

Run the power tool at no load and allow it to cool

down, replace or charge the rechargeable battery

soon, or press the KickBack button

Illuminated red Power tool has overheated or rechargeable bat-

tery is empty Allow the power tool to cool down, or replace or

charge the rechargeable battery

Flashing red KickBack shutdown has been triggered Switch the power tool off and on again

Flashing blue Power tool is connected to a mobile device or

settings are being transferred –

Status indicator for power tool(9) Meaning/cause

Green Selected angle is reached with a tolerance of +/–3° to the taught-in surfaceA)

1 609 92A 838 | (14.07.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSB 18V-150 C Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info