592527

Bosch GSC 10.8 V-LI Professional Seite 12

12
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
12 | English
1 609 92A 0NT | (23.5.14) Bosch Power Tools
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
– Insert the charged battery 2 into the handle until it can be
felt to engage and faces flush against the handle.
Switching On and Off
–To start the machine, push the On/Off switch 5 forward so
that the “I” is indicated on the switch.
–To switch off the machine, push the On/Off switch 5 to-
ward the rear so that the “0” is indicated on the switch.
To save energy, only switch the power tool on when using it.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Note: If the machine should automatically switch off because
of a discharged or overheated battery, make sure to set the
machine’s On/Off switch 5 to off. Charge the battery and al-
low it to cool down before restarting the machine. Otherwise
the battery can become damaged.
Working Advice
– Apply the power tool to the workpiece only when switched
on.
– Guide the power tool at an angle of 80 to 90 ° to the surface
of the sheet metal and do not tilt it to the side.
– Guide the machine evenly and with light feed in the cutting
direction. Excessive feed significantly reduces the service
life of the saw blade and can cause damage to the power
tool.
– When cutting curves, make sure not to tilt the power tool
laterally and work with low feed rate only.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on
the strength properties of the material to be cut.
The machine allows for cutting of metal sheet to the following
thicknesses:
Adjusting Cutter Clearance a
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
The cutter clearance a (gap between the
cutters) depends on the sheet thickness
d
max
to be cut.
The cutter clearance a should be 10 % of
the sheet thickness d
max
(e. g. 0.1 mm cut-
ter clearance for 1 mm sheet thickness).
For softer or more ductile materials, the
clearance a must be decreased; for harder
or more brittle materials, increased.
– Loosen the fastening screw 13 for the bottom cutter. Ad-
just the required cutter clearance a with the adjustment
screw 12. The upper cutter 10 and the bottom cutter 11
may not touch each other. Check the clearance with the
setting gauge 14. Retighten the fastening screw 13 for the
bottom cutter with a tightening torque of 3–4 Nm.
Temperature Dependent Overload Protection
If used in accordance with its intended use, the power tool
cannot be overloaded. If the power tool is overloaded or not
kept within the permitted battery temperature range, the
stroke rate is reduced or the power tool switches off. When
the stroke rate is reduced, the power tool will not run at full
stroke rate again until the permitted battery temperature has
been reached. If it automatically shuts down, switch the pow-
er tool off, allow the battery to cool down, then switch the
power tool back on.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature range between
–20 °C and 50 °C. As an example, do not leave the battery in
the car in summer.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
Material Max. strength property
[N/mm
2
]
d
max
[mm]
Steel 400 1.3
600 0.8
800 0.6
Aluminium 250 2.0
80–90
˚
a
OBJ_BUCH-840-006.book Page 12 Friday, May 23, 2014 12:04 PM
… 12 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GSC 10.8 V-LI Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info