592526
13
Zoom out
Zoom in
Vorherige Seite
1/79
Nächste Seite
English | 13
Bosch Power Tools 1 609 929 M52 | (1.4.09)
Declaration of Conformity
We declare under our sole responsibility that
the product described under “Technical Data”
is in conformity with the following standards
or standardization documents: EN 60745 ac-
cording to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 12.09.2007
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forwards.
To lock the On/Off switch 1, additionally push
down the front of the switch.
To switch off the machine, release the On/Off
switch 1. When the On/Off switch is locked, press
on the rear of the switch and then release it.
Working Advice
f The power tool is not suitable for stationary
operation. For example, it may not be
clamped in a vice or fastened on a workbench.
f Only work with the chip deflector 2 mount-
ed. Take care that the chip deflector is not
damaged or bent. Danger of injury when
working without the chip deflector or when it
is damaged. Have a damaged chip deflector
replaced immediately by an after-sales
service centre for Bosch power tools.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Take care that cut sheet parts do not bend
toward your body or the mains cable. Sharp
burrs develop at the cut steel sheet and can
cause injuries to the operator or damage the
mains cable. If required, press bending steel
sheet parts away from your body or the
mains cable using gloves.
Apply the power tool to the workpiece only
when switched on.
Guide the power tool at an angle of 80 to 90° to
the surface of the sheet metal and do not tilt it
to the side.
Guide the machine evenly and with light feed in
the cutting direction. Excessive feed significantly
reduces the service life of the saw blade and can
cause damage to the power tool.
When cutting curves, make sure not to tilt the
power tool laterally and work with low feed rate
only.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
80–90
˚
OBJ_BUCH-460-002.book Page 13 Wednesday, April 1, 2009 3:34 PM
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GSC 160 Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch GSC 160 Professional

Bosch GSC 160 Professional Bedienungsanleitung - Polnisch - 89 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info