Bedienungsanleitung Bosch GSC 160 Professional (Seite 14 von 79) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592526

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

14 | English

1 609 929 M52 | (1.4.09) Bosch Power Tools

Maximum Steel Sheet Cutting Capacity

The maximum steel sheet cutting capacity d

max

depends on the strength properties of the ma-

terial to be cut.

The machine allows for cutting of metal sheet to

the following thicknesses:

Adjusting Cutter Clearance a

f Before any work on the machine itself, pull

the mains plug.

The cutter clearance a (gap be-

tween the cutters) depends on

the sheet thickness d

max

to be cut.

For softer or more ductile materials, the clear-

ance a must be decreased; for harder or more

brittle materials, increased.

Loosen the fastening screw 7 for the bottom cut-

ter. Adjust the required cutter clearance a with

the adjustment screw 6. The upper cutter 4 and

the bottom cutter 5 may not touch each other.

Retighten the fastening screw 7 for the bottom

cutter with a tightening torque of 3–4 Nm.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

Replacing the blade (see figure A)

The upper cutter 4 and the bottom cutter 5 are

identical, have four cutting edges each, and can

be exchanged with each other.

Turn or replace the cutters in good time. Only

sharp application tools achieve good cutting

capacity and make the machine last longer.

To replace the upper cutter 4, loosen the fasten-

ing screw 3; to replace the bottom cutter 5,

loosen the fastening screw 7.

Turn the cutter by 90° or install a new cutter.

When installing the bottom cutter 5, pay atten-

tion that it faces against the adjustment screw 6.

Note: Turn the cutter only in the direction indi-

cated in the figure and insert a new cutter only

in the position shown in the figure. Cutting is

not possible with an incorrectly inserted cutter.

Retighten the fastening screw 3 for the upper

cutter and the fastening screw 7 for the bottom

cutter with a tightening torque of 3–4 Nm.

Check the cutter clearance a (see “Adjusting

Cutter Clearance a”, page 14).

Upper cutter 4 and bottom cutter 5 may not be

reground.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article

number given on the type plate of the machine.

Material Max. strength property

[N/mm

]

max

[mm]

Steel 400 1.6

600 1.2

800 0.7

Aluminium 200 2.2

max

[mm]

Cutter clearance a

[mm]

0.3–0.6 0.10

0.8–1.2 0.25

1.3–1.6 0.30

OBJ_BUCH-460-002.book Page 14 Wednesday, April 1, 2009 3:34 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSC 160 Professional Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GSC 160 Professional

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info