592525
14
Zoom out
Zoom in
Vorherige Seite
1/85
Nächste Seite
1 609 929 N55 | (14.11.07) Bosch Power Tools
14 | English
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Switching On and Off
To start the machine, push the On/Off switch 1
forward so that the “I” is indicated on the switch.
To switch off the machine, push the On/Off
switch 1 toward the rear so that the “0” is indi-
cated on the switch.
Working Advice
Apply the power tool to the workpiece only when
switched on.
Hold the power tool inclined in an angle of 15° to
the surface of the steel sheet and do not tilt it lat-
erally.
Guide the machine evenly and with light feed in
the cutting direction. Excessive feed significantly
reduces the service life of the saw blade and can
cause damage to the power tool.
f Wear protective gloves while working and
pay particular attention to the mains cable.
Sharp burrs develop at the cut steel sheet and
can cause injuries to the operator or damage
the mains cable.
When cutting curves, make sure not to tilt the pow-
er tool laterally and work with low feed rate only.
Maximum Steel Sheet Cutting Capacity
The maximum steel sheet cutting capacity d
max
depends on the strength properties of the ma-
terial to be cut.
The machine allows for cutting of metal sheet to
the following thicknesses:
Adjusting Cutter Clearance a
The cutter clearance a (gap be-
tween the cutters) depends on
the sheet thickness d
max
to be cut.
For softer or more ductile materials, the
clearance a must be decreased; for harder or
more brittle materials, increased.
Loosen the fastening screw 12 for the bottom
cutter. Adjust the requested cutter clearance a
with the adjustment screw 11. The upper cutter
7 and the bottom cutter 9 may not touch each
other. Check the clearance with the setting
gauge 13. Retighten the fastening screw 12 for
the bottom cutter.
15
˚
Material Max. strength property
[N/mm
2
]
d
max
[mm]
Steel 400 2.8
600 2.2
800 1.9
Aluminium 200 3.5
d
max
[mm]
Cutter clearance a
[mm]
0.2
1.4 0.3
1.5
2.8 0.5
a
OBJ_BUCH-598-001.book Page 14 Wednesday, November 14, 2007 10:16 AM
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GSC 2.8 Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info