Bedienungsanleitung Bosch GSC 2.8 Professional (Seite 15 von 85) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

592525

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

English | 15

Bosch Power Tools 1 609 929 N55 | (14.11.07)

Adjusting Cutter Clearance b

For adjustment of cutter

clearance b, the stroke

mechanism of the upper cut-

ter must be at the upper

dead centre point. For this,

briefly switch the power tool

on and then immediately off

again. If the stroke mechanism does not stop at

the upper dead centre point, repeat the process.

Screw the adjustment screw for the upper cutter

5 in clockwise direction using a fitting pin. Loos-

en the fastening screw for the upper cutter 8 and

adjust the upper cutter 7 in such a manner that

the vertical clearance b between upper and bot-

tom cutter is 0.4 mm. Check the clearance with

the setting gauge 13.

Retighten the fastening screw 8 for the upper

cutter. Screw the adjustment screw for the up-

per cutter 5 in anticlockwise direction until it fac-

es against the upper cutter 7.

For softer or more ductile materials, the

clearance b must be decreased; for harder or

more brittle materials, increased.

Maintenance and Service

Maintenance and Cleaning

f Before any work on the machine itself, pull

the mains plug.

f For safe and proper working, always keep

the machine and ventilation slots clean.

Replacing the Bottom Cutter (see figure B)

Unscrew the adjustment screw 11 of the bottom

cutter. Fully unscrew the fastening screw 12 of the

bottom cutter and remove the bottom cutter 9.

Insert a new bottom cutter 9 into the recess of

the cutting base 10. Fasten the bottom cutter

with the fastening screw 12.

Check the cutter clearance a (see “Adjusting

Cutter Clearance a”, page 14).

Replacing the Upper Cutter (see figure B)

Both sides of the upper cutter 7 can be used.

Fully unscrew the fastening screw 8 of the upper

cutter and remove the upper cutter 7.

Turn the upper cutter 7 as shown in the figure or

place a new upper cutter against the striker 6.

Fasten the upper cutter with fastening screw 8.

Check the cutter clearance b (see “Adjusting

Cutter Clearance b”, page 15).

Regrinding the Cutters (see figure C)

Replace or regrind worn cutters in good time.

Only sharp tools achieve good cutting capacity

and make the machine last longer.

When regrinding the cutters, take care that the

cutting angles are maintained.

Check the cutting angles with the setting gauge 13.

WARNING! Important instructions for connect-

ing a new 3-pin plug to the 2-wire cable.

The wires in the cable are coloured according to

the following code:

Do not connect the blue or brown wire to the

earth terminal of the plug.

Important: If for any reason the moulded plug is

removed from the cable of this power tool, it

must be disposed of safely.

If the machine should fail despite the care taken

in manufacturing and testing procedures, repair

should be carried out by an after-sales service

centre for Bosch power tools.

In all correspondence and spare parts order,

please always include the 10-digit article number

given on the type plate of the machine.

OBJ_BUCH-598-001.book Page 15 Wednesday, November 14, 2007 10:16 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GSC 2.8 Professional Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info