Bedienungsanleitung Bosch gsr 12 0 vsh 2 (Seite 23 von 279) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

381287

Zoom out

Zoom in

Vorherige Seite

1/279

Nächste Seite

English | 23

Bosch Power Tools 2 609 932 649 | (17.8.09)

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch O-pack batteries

with the voltage given on the type plate of

your machine. The use of other batteries can

lead to injuries and danger of fire.

Set the rotational direction switch 9 to the cen-

tre position in order to avoid unintentional start-

ing. Insert the charged battery 7 into the handle

so that it can be felt to engage and faces flush

against the handle.

Reversing the Rotational Direction

(see figure F)

The rotational direction switch 9 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 10 actuated.

Right Rotation: For drilling and driving in

screws, push the rotational direction switch 9

left to the stop.

Left Rotation: For loosening or unscrewing

screws, push the rotational direction switch 9

right to the stop.

Setting the Torque

With the torque presetting ring 2 the required

torque setting can be preselected in 25 steps.

With the correct setting, the insert tool is

stopped as soon as the screw is screwed flush

into the material or when the adjusted torque is

reached. The safety clutch is deactivated in the

“ ” position, e. g. for drilling.

Select a higher setting or switch to the

“ ” symbol when unscrewing screws.

Setting range 1–20:

Lower torque for screwing in screws with small

diameter or into soft materials. Fine torque gra-

dients between the individual setting positions.

Setting range 21–25:

Higher torque for screwing in screws with large di-

ameters or into hard materials. Coarse torque gra-

dients between the individual setting positions.

Setting the Operating Mode (GSB 12 VE-2/

GSB 14,4 VE-2/GSB 18 VE-2) (see figure G)

With the operating mode preselection ring 4,

you can select between drilling/screwdriving

and impact drilling.

Drilling and screwdriving

Set the preselection ring 4 to the

“Drilling without impact” symbol.

Impact drilling

Set the preselection ring 4 to the

“Impact drilling” symbol.

In the “Impact drilling” position, the safety

clutch is deactivated and the maximum power is

always effective.

Gear Selection, Mechanical

f Actuate the gear selector 3 only when the

machine is at a standstill.

Two speed ranges can be preselected with the

gear selector 3.

Gear I:

Low speed range; for screwdriving or working

with large drilling diameter.

Gear II:

High speed range; for working with small drilling

diameter.

If the gear selector 3 cannot be pushed through

to the stop, lightly turn the drill chuck with drill.

OBJ_BUCH-199-004.book Page 23 Monday, August 17, 2009 8:32 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gsr 12 0 vsh 2 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info