Bedienungsanleitung Bosch GST 18 V-LI S Professional (Seite 18 von 277) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708174

Zoom out

Zoom in

Vorherige Seite

1/277

Nächste Seite

18 | English

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

u Do not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

The battery (3) is equipped with two locking levels to pre-

vent the battery from falling out if the battery release button

(4) is pressed unintentionally. The battery is held in place by

a spring when fitted in the power tool.

To remove the battery (3), press the release button (4) and

pull the battery out of the power tool. Do not use force to

do this.

Battery charge indicator

The green LEDs on the battery charge indicator(18) indic-

ate the battery's state of charge(3). For safety reasons, it is

only possible to check the state of charge when the power

tool is not in operation.

Press the button for the battery charge indicator(17) to

show the state of charge. This is also possible when the bat-

tery is removed.

If no LED lights up after pressing the button for the battery

charge indicator(17), then the battery is defective and must

be replaced.

Battery modelGBA18V… (seefigureA)

LEDs Capacity

3× continuous green light 60−100%

2× continuous green light 30−60%

1× continuous green light 5−30%

3× flashing green light 0−5%

Battery modelProCORE18V… (seefigureB)

LEDs Capacity

5× continuous green light 80−100%

4× continuous green light 60−80%

3× continuous green light 40−60%

2× continuous green light 20−40%

1× continuous green light 5−20%

1× flashing green light 0−5%

Inserting/changing the saw blade

u When fitting or changing the saw blade, wear protect-

ive gloves. Blades are sharp and can become hot when

used for prolonged periods of time.

Selecting the saw blade

You will find an overview of recommended saw blades at the

end of these operating instructions. Only use saw blades

with single lug shank (T shank). The saw blade should not be

longer than required for the intended cut.

Use a narrow saw blade when sawing tight curves.

Inserting the saw blade (seefigure C)

u Clean the shaft on the saw blade before inserting it.

Adirty shaft cannot be securely fixed in place.

Push the saw blade (10), with the teeth in the cutting direc-

tion, into the saw blade receptacle (19) until it clicks into

place. The SDS lever (11) automatically springs back and

the saw blade is locked in place. Do not push the lever (11)

back by hand as you could damage the power tool.

Make sure when inserting the saw blade that the back of the

saw blade is in the groove on the guide roller (9).

u Check that the saw blade is seated securely. A loose

saw blade can fall out and lead to injuries.

Ejecting the saw blade (seefigure D)

u When ejecting the saw blade, hold the power tool in

such a manner that no persons or animals can be in-

jured by the ejected saw blade.

Turn the SDS lever (11) as far as it will go in the direction of

the shock protection guard (13). The saw blade is released

and ejected.

Glide shoe (see figure E)

The plastic guide plate(6) of the base plate(7) reduces

scratching on sensitive surfaces. Use the steel glide

shoe(20) when machining metal.

Fit the steel glide shoe(20) by sliding it onto the base

plate(7) from the front.

The plastic guide plate(6) should be replaced if it is worn.

Anti-splinter guard (see figureF)

The anti-splinter guard (21) (accessory) can prevent splin-

tering of the surface while sawing wood. The anti-splinter

guard can only be used with certain saw blade types and only

at a cutting angle of 0°. When sawing with the anti-splinter

guard, the base plate (7) must not be moved to the rear for

sawing close to edges.

Slide the anti-splinter guard (21) into the base plate (7)

from the front.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

1 609 92A 4TM | (04.04.2019) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GST 18 V-LI S Professional Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info