Bedienungsanleitung Bosch GST 18 V-LI S Professional (Seite 19 von 277) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708174

Zoom out

Zoom in

Vorherige Seite

1/277

Nächste Seite

English | 19

The regulations on the material being machined that apply in

the country of use must be observed.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Connecting the dust extraction (see figures G–H)

Fit the extraction outlet(22) in the recesses of the base

plate(7).

Connect a dust extraction hose (23) (accessory) to the ex-

traction outlet (22). Connect the dust extraction hose (23)

to a dust extractor (accessory).

You will find an overview of connecting to various dust ex-

tractors at the end of these operating instructions.

For optimum dust extraction, where possible use the anti-

splinter guard (21).

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Operation

Operating modes

u Remove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Pendulum action settings

The pendulum action can be adjusted using four different

settings, allowing the cutting speed, cutting capacity and the

cut itself to be optimally adapted to the material that you

want to cut.

You can also adjust the pendulum action during operation

using the adjusting lever (8).

No pendulum action

Low pendulum action

Moderate pendulum action

High pendulum action

The optimum pendulum level for each application can be de-

termined by a practical test. Note the following recommend-

ations:

– Select a lower pendulum level or switch off the pendulum

action completely if you wish to produce a finer or cleaner

cutting edge.

– Switch off the pendulum action when machining thin ma-

terials (e.g. sheets).

– Work on hard materials (e.g. steel) with low pendulum ac-

tion.

– You can work on soft materials and saw wood in the direc-

tion of the grain using maximum pendulum action.

Setting the mitre/bevel angle (see figureI)

(GST18V‑LIB)

The base plate (7) can be swivelled to the right or left to

make mitre cuts up to 45°.

The extraction outlet (22) and anti-splinter guard (21) can-

not be used while mitre/bevel cuts are being made.

– Remove the extraction outlet (22) and the anti-splinter

guard (21).

– Loosen the screw (24) with the hex key (5) and slide the

base plate (7) all the way towards the battery (3).

– The base plate has lock-in points at 0° and 45° on the left

and right so that precise mitre/bevel angles can be set.

Swivel the base plate (7) to the desired position accord-

ing to the scale (25). Other mitre/bevel angles can be ad-

justed using a protractor.

– Then push the base plate (7) towards the saw blade (10)

as far as it will go.

– Retighten the screw (24).

Moving the base plate (see figureI) (GST18V‑LIB)

You can move the base plate (7) back for sawing close to

edges.

Loosen the screw of the base plate (24) with the hex key (5)

and slide the base plate (7) all the way towards the battery

(3).

Retighten the screw (24).

Sawing with an offset base plate (7) is only possible with a

mitre angle of 0°. In all other cases the anti-splinter guard

(21) may not be used.

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Slide the charged battery (3) from below into the foot of the

power tool. Press the battery fully into the base until the bat-

tery is securely locked.

Switching on the LED worklight (GST18V‑LIS)

To switch the worklight(12) on or off, press the worklight

button(15).

u Do not look directly into the worklight; it can blind

you.

Switching On and Off (GST18V‑LIS)

u Make sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, slide the on/off switch(2) for-

wards so that "I" appears on the switch.

To switch off the power tool, slide the on/off switch(2)

backwards so that "0" appears on the switch.

Switching On and Off (GST18V‑LIB)

To switch on the power tool, press the lock-off button (1)

next to the symbol first, thereby deactivating it. Then

press the on/off switch (2) and keep it pressed.

Bosch Power Tools 1 609 92A 4TM | (04.04.2019)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GST 18 V-LI S Professional Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info