Bedienungsanleitung Bosch GTB 12V-11 (Seite 13 von 171) (Alle Sprachen)

786154

Zoom out

Zoom in

Vorherige Seite

1/171

Nächste Seite

English | 13

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Battery Charging

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the battery

To remove the battery (7), press the release buttons (6) and

pull the battery back and out of the power tool. Do not use

force to do this.

Changing the Tool (see figure A)

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Pull the depth stop (4) off towards you. Pull the screwdriver

bit (1) out. If required, the universal bit holder (11) can also

be pulled out and replaced.

An auxiliary tool can be used to remove the screwdriver bit

or universal bit holder.

After changing the tool, reattach the depth stop (4).

Operation

Starting Operation

Inserting the Battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (5) to the middle position

to avoid unintentionally switching it on. Insert the charged

battery (7) into the handle until you feel it engage and it is

flush with the handle.

Setting the Rotational Direction

The rotational direction switch (5) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (10) is being pressed.

Right rotation: Slide the rotational direction switch

(5) all the way into position on both sides.

Left rotation: Slide the rotational direction switch (5)

all the way into position on both sides.

Switching on/off

To start the power tool, press and hold the on/off switch

(10).

The LED (9) lights up when the on/off switch (10) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (10).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (10) to varying extents.

A light pressure on the on/off switch (10) results in a low ro-

tational speed. Increased pressure on the switch causes an

increase in speed.

Adjusting the screw-in depth (see figure B)

The depth to which the screw head is screwed into the work-

piece can be preset by turning the adjusting sleeve (3) to 8

engaging steps for each rotation. Each step corresponds to a

0.25 mm change in the screw-in depth.

Turning the adjusting sleeve (3) clockwise increases the

screw-in depth; turning it anticlockwise decreases the

screw-in depth.

The best way to determine the setting you require is to drive

in some test screws.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or not kept within the

permitted battery temperature range, the power output is

reduced or the power tool is switched off. The power tool

will not run at full power output again until the permitted bat-

tery temperature has been reached.

Practical advice

uOnly apply the power tool to the screw when the tool

is switched off. Rotating application tools can slip off.

Place the screw against the screwdriver bit(1). The screw

will be held in place by the magnetic retention force of the

universal bit holder(11). Forcefully press the tip of the

screw against the material you wish to screw until the screw

depth stop(4) rests on the workpiece.

Switch the power tool on. The screw is screwed into the

workpiece until it reaches the set screw depth. The drive is

Bosch Power Tools 1 609 92A 7PT | (02.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GTB 12V-11 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info