Bedienungsanleitung Bosch GTK 40 (Seite 16 von 157) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544370

Zoom out

Zoom in

Vorherige Seite

1/157

Nächste Seite

1 609 929 U13 | (17.8.12) Bosch Power Tools

16 | English

– Lightly pull back magazine slider 11 and press the but-

ton of magazine-slider lock 7 inward.

– Carefully guide the magazine slider to the front until it

touches the beginning of the magazine.

Note: Do not let the magazine slider snap back without

guiding it. Otherwise, the magazine slider could become

damaged, and there is danger of your fingers being caught

or pinched.

GSK 50

– Press magazine lock 14 and at the same time pull maga-

zine 8 toward the rear to the stop.

– Remove the nail strips 19.

– Insert the magazine until magazine lock 14 engages

again.

Adjusting the Depth Stop (see figure F)

The driving depth of the staples (GTK 40) or brads

(GSK 50) can be set with thumbwheel 3.

– Empty the magazine 8.

(See “Emptying the Magazine”, page 15)

– Nails are driven in too deeply:

To reduce the driving depth, turn thumbwheel 3 in anti-

clockwise direction.

Nails are not driven in deep enough:

To increase the driving depth, turn thumbwheel 3 in

clockwise direction.

– Refill the magazine.

(See “Loading the Magazine”, page 15)

– Test the new driving depth on a test workpiece.

Repeat the worksteps as required.

Clearing Jams

Single staples (GTK 40) or brads (GSK 50) can become

jammed in the shot duct. If this should occur frequently,

please contact an authorised service agent for Bosch pow-

er tools.

Note: When the driver blade does not return after clearing

a jam, please contact an authorised service agent for

Bosch power tools.

GTK 40 (see figures G1–G3)

– Empty the magazine 8.

(See “Emptying the Magazine”, page 15)

– Press clamping lever 12 down so that the shot duct

opens.

– Remove the jammed staple. For this, us a pair of pliers,

if required.

– When driver blade 21 is extended, push it back into the

piston using a lubricated screwdriver or other suitable

lubricated object.

– Lubricate the shot duct with 2–3 drops of engine oil

(SAE 10 or SAE 20).

– Close the shot duct, hang the clip of clamping lever 12

into the hooks on the shot duct and then push the

clamping lever up again.

– Refill the magazine.

(See “Loading the Magazine”, page 15)

GSK 50 (see figure H)

– Empty the magazine 8.

(See “Emptying the Magazine”, page 15)

– With the magazine open, remove the jammed brad. For

this, us a pair of pliers, if required.

– When driver blade 21 is extended, push it back into the

piston using a lubricated screwdriver or other suitable

lubricated object.

– Lubricate the shot duct with 2–3 drops of engine oil

(SAE 10 or SAE 20).

– Refill the magazine.

(See “Loading the Magazine”, page 15)

Changing the Workpiece Protector (see figure I)

The workpiece protector 1 at the end of the discharge lock-

off 2 protects the workpiece until the pneumatic tool is cor-

rectly placed for the driving procedure.

The workpiece protector can be removed and replaced.

– Pull the workpiece protector from the discharge lock-

off.

– Push the new workpiece protector via the open end

over the discharge lock-off.

GSK 50: This pneumatic tool allows for a spare workpiece

protector to be stored at the top side of magazine 8. For

this, push the workpiece protector into the depot 22.

Adjustable Air-outlet cap (see figure J)

With the adjustable exhaust cap at the air outlet 4, it is pos-

sible to deflect the exhaust air away from yourself or the

workpiece.

Transport and Storage

For transport, disconnect the pneumatic tool from the air

supply; especially when using ladders or moving in an unu-

sual stance or posture.

At the workplace, carry the pneumatic tool only by the han-

dle 5 and with the trigger 10 released.

Always store the pneumatic tool disconnected from the air

supply and at a clean and dry location.

When not using the pneumatic tool for a longer period of

time, cover steel parts with a fine oil coating. This prevents

the formation of rust.

Maintenance and Service

Maintenance and Cleaning

Disconnect the air supply before making

any adjustments, changing accessories,

or placing the pneumatic tool aside. This

safety measure prevents accidental start-

ing of the pneumatic tool.

If the pneumatic tool should fail despite the

care taken in manufacture and testing, repair should be

carried out by an authorised customer services agent for

Bosch power tools.

In all correspondence and spare parts orders, please al-

ways include the 10-digit article number given on the type

plate of the pneumatic tool.

f Have maintenance and repair work carried out only

through qualified persons. This will ensure that the

safety of the pneumatic tool is maintained.

An authorized Bosch after-sales service agent will carry out

this work quickly and reliably.

Lubricating the Pneumatic Tool (see figure K)

When the pneumatic tool is not connected to a mainte-

nance unit, it must be lubricated at regular intervals:

–For light-duty use 1x per day.

–For heavy-duty use 2x per day.

Apply 2–3 drops of lubricant into air connector 6. Do not

apply too much lubricant, which could then accumulate in

the pneumatic tool and be emitted via air outlet 4.

Use only the lubricants recommended by Bosch.

– SAE 10 mineral engine oil (for use at very cold ambient

conditions)

– SAE 20 mineral engine oil

f Observe all applicable environmental regulations

when disposing of old grease and solvents.

Maintenance Schedule

Always keep air outlet 4, discharge lock-off 2 and trigger

10 clean and free of foreign material (dust, chips, sand,

etc).

Clean the magazine 8. Remove any plastic or wood chips

that may accumulate in the magazine during operation.

Clean the pneumatic tool in regular intervals using com-

pressed air.

Measure Explanation Action

Draining the exhaust filter daily.

Prevents the accumulation of dirt/ debris and moisture in the

pneumatic tool.

– Open the drain valve.

Keeping the lubricator filled at all times.

Ensures the lubrication of the pneumatic tool. – Fill lubricator with the recommended lubricants.

(See “Lubricating the Pneumatic Tool”, page 16)

Cleaning the magazine 8 and magazine slider 11.

Prevents a staple (GTK 40) or brad (GSK 50) from becoming

jammed.

– Blow out the mechanism of the magazine/magazine

slider daily with compressed air.

Ensuring that the discharge lock-off 2 functions properly.

Promotes your work safety and efficient usage of the pneu-

matic tool.

– Blow out the mechanism of the discharge lock-off daily

with compressed air.

Lubricating the pneumatic tool.

Reduces the wear of the pneumatic tool. – Apply 2–3 drops of lubricant into air connector 6.

(See “Lubricating the Pneumatic Tool”, page 16)

Draining the compressor.

Prevents the accumulation of dirt/ debris and moisture in the

pneumatic tool.

– Open the drain valve of the compressor tank.

OBJ_BUCH-1038-003.book Page 16 Friday, August 17, 2012 10:59 AM

Bosch GTK 40 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info