Bedienungsanleitung Bosch GTK 40 (Seite 17 von 157) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544370

Zoom out

Zoom in

Vorherige Seite

1/157

Nächste Seite

English | 17

Bosch Power Tools 1 609 929 U13 | (17.8.12)

Correction of Malfunctions

Accessories

For more information on the complete quality accessories

program, please refer to the Internet under

www.bosch-pt.com or contact your specialist shop.

Problem Cause Corrective Measure

The pneumatic tool is ready for operation, but no staples

(GTK 40) or brads (GSK 50) are discharged.

A staple (GTK 40) or a brad (GSK 50) has become jammed in

the shot duct.

–Clear the jam.

(See “Clearing Jams”, page 16)

The magazine slider is 11 defective. – Clean and lubricate the magazine slider 11 as required

and make sure that the magazine 8 is not dirty/soiled.

The spring of the magazine slider is too week or defective. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

The fasteners being used are not permitted. – Use only original accessories.

Only the fasteners (nails, staples, etc.) specified in ta-

ble “Technical Data” may be used.

The magazine 8 is empty. – Refill the magazine.

(See “Loading the Magazine”, page 15)

The staples (GTK 40) or brads (GSK 50) are discharged very

slowly and with too little pressure.

The rated pressure of the compressed-air supply is too low. – Increase the compressed-air supply. 8 bar may not be

exceeded.

The driver blade is damaged. – Use only the lubricants recommended by Bosch.

(See “Lubricating the Pneumatic Tool”, page 16)

The sealing ring of the piston is worn or damaged. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

The buffer is worn. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

The length and diameter of supply-air hose 17 do not corre-

spond with the data of this pneumatic tool.

– Use a supply-air hose with the correct dimensions.

(See “Technical Data”, page 14)

The supply-air hose 17 is bent/creased. – Correct the bend/crease in the supply-air hose.

The staples (GTK 40) or brads (GSK 50) are driven in too

deep.

The rated pressure of the compressed-air supply is too high. – Reduce the compressed-air supply. 5 bar may not be

fallen below.

The depth stop is set too deep. – Adjust the depth stop to the desired depth.

(See “Adjusting the Depth Stop”, page 16)

The buffer is worn. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

The staples (GTK 40) or brads (GSK 50) are not driven in

deep enough.

The rated pressure of the compressed-air supply is too low. – Increase the compressed-air supply. 8 bar may not be

exceeded.

The depth stop is set too high. – Adjust the depth stop to the desired depth.

(See “Adjusting the Depth Stop”, page 16)

The length and diameter of supply-air hose 17 do not corre-

spond with the data of this pneumatic tool.

– Use a supply-air hose with the correct dimensions.

(See “Technical Data”, page 14)

The supply-air hose 17 is bent/creased. – Correct the bend/crease in the supply-air hose.

The pneumatic tool skips staples (GTK 40) or brads (GSK 50)

or has a too large cycle feed.

The fasteners being used are not permitted. – Use only original accessories.

Only the fasteners (nails, staples, etc.) specified in ta-

ble “Technical Data” may be used.

The magazine 8 is not operating correctly. – Clean and lubricate the magazine slider 11 as required

and make sure that the magazine 8 is not dirty/soiled.

The spring of the magazine slider is too week or defective. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

The sealing ring of the piston is worn or damaged. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

The staples (GTK 40) or brads (GSK 50) frequently jam in the

shot duct.

The fasteners being used are not permitted. – Use only original accessories.

Only the fasteners (nails, staples, etc.) specified in ta-

ble “Technical Data” may be used.

– Contact an authorised service agent for Bosch power

tools.

The driven staples (GTK 40) or brads (GSK 50) are bent.

The driver blade is damaged. – Contact an authorised service agent for Bosch power

tools.

Have the component replaced there.

Contrary to working with normal operating speed, the staples

(GTK 40) or brads (GSK 50) are not driven in deep enough

enough at higher operating speeds.

The interior diameter of the supply-air hose is too low. – Use a supply-air hose with the correct dimensions.

(See “Technical Data”, page 14)

The compressor is not suitable for fast operating speeds. – Use a compressor that is sufficiently dimensioned for

the number of connected pneumatic tools and the op-

erating speed.

OBJ_BUCH-1038-003.book Page 17 Friday, August 17, 2012 10:59 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GTK 40 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info