Bedienungsanleitung Bosch GUS 12V-300 (Seite 13 von 175) (Alle Sprachen)

786107

Zoom out

Zoom in

Vorherige Seite

1/175

Nächste Seite

English | 13

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Assembly

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Battery Charging

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Removing the Battery (seefigureA)

To remove the battery(6), press the battery release

buttons(7) and pull the battery out of the power tool. Do

not use force to do this.

Battery charge indicator

The three green LEDs on the battery charge indicator(9) in-

dicate the state of charge of the battery(6). For safety reas-

ons, it is only possible to check the state of charge when the

power tool is not in operation.

To display the state of charge, press and hold the battery

charge indicator button(8) when the power tool is switched

off.

LEDs Capacity

3× continuous green light ≥66%

2× continuous green light ≥33%

1× continuous green light <33%

1× flashing green light Reserve

Changing the Tool (seefiguresB1−B2)

uBefore removing, allow the blade to cool down. The

blade can become warm during operation.

– Loosen the knurled screw(1) and push the protective

guard(3) all the way to the top.

– Use a screwdriver to turn the blade(10) until a hole

opens in the blade.

– Insert a thin, stable object (e.g. a nail) in the open hole in

order to block the blade.

– Undo the screw for securing the blade(11) in rotational

direction.

– Remove the object used to block the blade.

– Lift the blade(10) slightly and pull it down and out.

– Place the blade on the tool holder with the ground edge

facing outwards. Ensure that the blade clicks into place in

the tool holder.

– Retighten the screw for securing the blade(11) in rota-

tional direction .

– Adjust the protective guard(3) to the material thickness

to be cut and tighten the knurled screw(1).

Adjusting the Protective Guard

uNever use the power tool without the protective

guard.

To protect your fingers from injuries, the protective

guard(3) must be adjusted to the material thickness being

cut before each work step.

To do this, loosen the knurled screw(1). Adjust the protect-

ive guard(3) (in the range 2−11mm) so that it loosely rests

against the material to be cut. Retighten the knurled screw.

Adjust the protective guard(3) to the bottom position after

each use as well as before all work on the power tool.

Operation

Starting Operation

Inserting the Battery

Insert the charged battery(6) into the battery receptacle,

making sure you feel it engage and that it is securely locked

in place.

Switching On and Off

To switch on the power tool, slide the on/off switch(4) for-

wards so that I appears on the switch.

Bosch Power Tools 1 609 92A 7ST | (18.05.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GUS 12V-300 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info