Bedienungsanleitung Bosch GWS 12V-76 (Seite 18 von 273) (Alle Sprachen)

786195

Zoom out

Zoom in

Vorherige Seite

1/273

Nächste Seite

18 | English

The stated vibration level applies to the main applications of

the power tool. However, if the power tool is used for differ-

ent applications, with different application tools or poorly

maintained, the vibration level may differ. This can signific-

antly increase the exposure to vibration over the total work-

ing period.

To estimate the exposure to vibration accurately, the times

when the tool is switched off or when it is running but not ac-

tually being used should also be taken into account. This can

significantly reduce the exposure to vibration over the total

working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping the hands warm,

and organising workflows correctly.

Fitting

Battery Charging

uUse only the chargers listed in the technical data. Only

these chargers are matched to the lithium-ion battery of

your power tool.

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the Battery (seefigureA)

To remove the battery(4), press the release buttons(5) and

pull the battery out of the power tool. Do not use force to

do this.

Battery charge indicator

LED Capacity

Continuous lighting 3x green 60–100%

Continuous lighting 2x green 30–60%

Continuous lighting 1x green 10–30%

Slowly flashing light 1 x green 0–10%

Fitting Protective Equipment

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Note: If the grinding disc breaks during operation or the

holding fixtures on the protective guard/power tool become

damaged, the power tool must be sent to the after-sales ser-

vice immediately; see the "After-Sales Service and Applica-

tion Service" section for addresses.

Protective guard for grinding

uAlways use the protective guard for grinding (7)

when grinding.

Protective guard for cutting

uAlways use the protective guard for cutting (10) when

cutting bonded abrasives.

uProvide sufficient dust extraction when cutting stone.

Fitting the Protective Guard (seefigureB)

Insert the protective guard for cutting(10) onto the protect-

ive guard for grinding(7) until this engages firmly.

Adjusting the Protective Guard (seefigureB)

Turn the protective guard to the required position and en-

sure the protective guard is engaged. No tool is required for

this.

Fitting the abrasive tools

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Clean the grinding spindle(8) and all parts to be mounted.

To tighten or loosen the abrasive tools, push the spindle lock

button(2) forwards and simultaneously turn the grinding

tool to fix the grinding spindle in place.

uDo not press the spindle lock button while the grind-

ing spindle is moving. The power tool may become dam-

aged if you do this.

Grinding/cutting disc

Pay attention to the dimensions of the abrasive tools. The

diameter of the hole must match that of the mounting flange.

Do not use an adapter or reducer.

When using diamond cutting discs, make sure that the direc-

tion of rotation arrow on the diamond cutting disc corres-

ponds to the direction of rotation of the machine (see direc-

tion of rotation arrow on the housing).

See the graphics page for fitting instructions.

To remove the grinding/cutting disc, push the spindle lock

button(2) forwards while simultaneously turning on the

grinding/cutting disc(12) in order to fix the grinding

spindle(8) in place (seefigureC1).

Use a hex key(13) to remove the clamping bolt with

washer(11) and take off the grinding/cutting disc (12)

(seefigureC2).

1 609 92A 6PJ | (12.07.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 12V-76 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info