Bedienungsanleitung Bosch GWS 12V-76 (Seite 19 von 273) (Alle Sprachen)

786195

Zoom out

Zoom in

Vorherige Seite

1/273

Nächste Seite

English | 19

To attach the grinding/cutting disc, screw in the clamping

bolt with washer(11). Tighten the bolt using the hex

key(13) until the washer of the bolt is flush with the grind-

ing/cutting disc(12) (seefigureC3).

Then push the spindle lock button(2) back again

(seefigureC4).

uAfter fitting the abrasive tool, check that the abrasive

tool is fitted correctly and can turn freely before

switching on the power tool. Make sure that the abras-

ive tool does not brush against the protective guard or

other parts.

Approved Grinding Tools

You can use all the abrasive tools mentioned in these operat-

ing instructions.

The permissible speed [min-1] or the circumferential speed

[m/s] of the abrasive tools used must at least match the val-

ues given in the table.

It is therefore important to observe the permissible rota-

tional/circumferential speed on the label of the abrasive

tool.

max. [mm] [mm]

D b d [min-1] [m/s]

76 7 10 19,500 80

Selecting the Grinding/Cutting Disc

Abrasive tool Material

Carbide Multi

Wheel Wood (with nails),

plastic, PVC, com-

posite materials,

acrylic glass,

plaster, copper

Expert for Inox Stainless steel,

steel

Best for Ceramic Tiles, ceramics

Best for Hard

Ceramic Tiles, hard porcel-

ain, fine stoneware

Dust/Chip Extraction

Dust from materials such as lead-containing coatings, some

wood types, minerals and metal can be harmful to one’s

health. Touching or breathing-in the dust can cause allergic

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Start-up

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Insert the charged battery(4) into the handle of the power

tool until you feel it engage and it is flush with the handle.

Switching on/off

To start the power tool, push the on/off switch (3) forward.

To lock the on/off switch (3) in position, push the on/off

switch (3) forward and down until it clicks into place.

To switch off the power tool, release the on/off switch (3);

or, if the switch is locked, briefly push the on/off switch (3)

backward and down and then release it.

uAlways check abrasive tools before using them. The

abrasive tool must be fitted properly and be able to

move freely. Carry out a test run for at least one

minute with no load. Do not use abrasive tools that are

damaged, run untrue or vibrate during use. Damaged

abrasive tools can burst apart and cause injuries.

Temperature monitoring/overload protection indicator

The red LED indicator(6) helps you to protect the battery

against overheating and the motor against overload.

If the LED indicator(6) is lit up permanently in red, the

temperature of the battery is too high and the power tool

switches off automatically.

– Switch the power tool off.

– Allow the battery to cool down before you carry on work-

ing.

If the LED indicator(6) is flashing red, then the power tool

is blocked and will switch off automatically.

Pull the power tool out of the workpiece.

The power tool will continue to work as soon as the blockage

is rectified.

Practical advice

uExercise caution when cutting slots in structural walls;

see the "Information on structural design" section.

uWhen cutting lightweight materials, take into account

the statutory provisions and recommendations of the

material manufacturer.

uClamp the workpiece if it is not secure under its own

weight.

uDo not load the power tool so heavily that it comes to a

stop.

Bosch Power Tools 1 609 92A 6PJ | (12.07.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 12V-76 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info