79075
24
Zoom out
Zoom in
Vorherige Seite
1/156
Nächste Seite
English | 251 609 929 L08 12.1.07
Approved Grinding Tools
All grinding tools mentioned in these operating
instructions can be used.
The permissible speed [rpm] or the circumferential
speed [m/s] of the grinding tools used must at least
match the values given in the table.
Therefore, observe the permissible rotational/cir-
cumferential speed on the label of the grinding tool.
Rotating the Machine Head
f Before any work on the machine itself, pull
the mains plug.
The machine head can
be rotated with respect
to the machine housing
in 90° steps. In this
manner, the On/Off
switch can be brought
into a more convenient
position for special
working situations,
e.g., for cutting opera-
tions using the cutting
guide with dust extrac-
tion protection guard
20/cut off stand or for
left-handed persons.
Completely unscrew the four screws. Rotate the
machine head carefully, without removing it from
the housing, to the new position. Screw in and
tighten the four screws again.
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
When operating the machine with power from mobile
generators that do not have sufficient reserve capacity
or are not equipped with suitable voltage control with
starting current amplification, loss of performance or
untypical behavior can occur upon switching on.
Please observe the suitability of the power generator
being used.
Switching On and Off
To start the power tool, press the On/Off switch 4
forward and then down.
To lock-on the pressed On/Off switch 4, push the
On/Off switch 4 further forward.
To switch off the power tool, release the On/Off
switch 4, or when it is locked, briefly press the On/Off
switch 4 and then release it.
Switch Version without Lock-on
(country-specific):
To start the power tool, press the On/Off switch 4
forward and then down.
To switch off the machine, release the On/Off switch
4.
f Check grinding tools before using. The
grinding tool must be mounted properly and
be able to move freely. Carry out a test run
for at least one minute with no load. Do not
use damaged, out-of-centre or vibrating
grinding tools. Damaged grinding tools can
burst and cause injuries.
Kickback stop
In case of a sudden drop in speed,
e. g. jamming while carrying out a sep-
arating cut, the power supply to the
motor is interrupted.
To restart the operation, switch the
On/Off switch 4 to the Off position
and start the machine again.
Restarting protection
The restarting protection feature prevents uncon-
trolled restarting of the machine after an interruption in
the power supply.
To restart the operation, switch the On/Off switch
4 to the Off position and start the machine again.
max.
[mm] [mm]
D b d [rpm] [m/s]
115
125
150
6
6
6
22,2
22,2
22,2
11000
11000
9300
80
80
80
115
125
––
11000
11000
80
80
75 30 M 14 11000 45
b
d
D
D
D
b
d
OBJ_BUCH-165-003.book Page 25 Friday, January 12, 2007 9:16 AM
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GWS 15-125 CITH wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Bosch GWS 15-125 CITH

Bosch GWS 15-125 CITH Bedienungsanleitung - Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch - 156 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info