Bedienungsanleitung Bosch GWS 15-125 CITH (Seite 25 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

79075

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

26 | English 1 609 929 L08 • 12.1.07

Reduced starting current

The electronic reduced starting current limits the

power consumption when switching the tool on and

enables operation from a 13 ampere fuse.

Constant Electronic Control

Constant electronic control holds the speed constant

at no-load and under load, and ensures uniform work-

ing performance.

Speed preselection (GWS 15-125 CIEH/GWS 15-125 CITH)

The required speed can be preselected with the thumbwheel 3 (also while running).

The data in the following table are recommended values.

Operating Instructions

f Exercise caution when cutting slots in struc-

tural walls; see Section “

Information on

Structures

”.

f Clamp the workpiece if it does not remain

stationary due to its own weight.

f Do not strain the machine so heavily that it

comes to a standstill.

f Grinding and cutting discs become very hot

while working; do not touch until they have

cooled.

Rough Grinding

f Never use a cutting disc for roughing.

The best roughing results are achieved when setting

the machine at an angle of 30° to 40°. Move the

machine back and forth with moderate pressure. In

this manner, the workpiece will not become too hot,

does not discolour and no grooves are formed.

Flap Disc

With the flap disc (accessory), curved surfaces and

profiles can be worked.

Flap discs have a considerably higher service life,

lower noise levels and lower sanding temperatures

than conventional sanding sheets.

Cutting Metal

f For cutting metal, always work with the pro-

tection guard for cutting 13.

When cutting, work with moderate feed, adapted to

the material being cut. Do not exert pressure onto the

cutting disc, tilt or oscillate the machine.

Do not reduce the speed of running down cutting

discs by applying sideward pressure.

The machine must

always work in an up-

grinding motion. Oth-

erwise, the danger

exists of it being

pushed uncon-

trolled out of the cut.

When cutting profiles

and square bar, it is

best to start at the

smallest cross sec-

tion.

Cutting Stone

f For cutting stone, always work with the cut-

ting guide with dust extraction protection

guard 20.

f The machine may be used only for dry cut-

ting/grinding.

For cutting stone, it is best to use a diamond cutting

disc. As a safety measure against jamming, the cutting

guide with dust extraction protection guard 20 must

be used.

Operate the machine only with dust extraction and

additionally wear a dust protection mask.

The vacuum cleaner must be approved for the extrac-

tion of masonry dust. Bosch provides suitable vacuum

cleaners.

Material Application Tool Thumbwheel 3

Metal Removing paint Sanding disc 2 –3

Wood, metall Brushing, rust removal Cup brush, sanding disc 3

Metal, masonry Sanding Sanding disc 4 –6

Metal Rough grinding Sanding disc 6

Masonry, stone Cutting Cutting disc and cutting guide

(Cutting masonry/stone is permitted

only with use of the cutting guide) 6

OBJ_BUCH-165-003.book Page 26 Friday, January 12, 2007 9:16 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 15-125 CITH Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch GWS 15-125 CITH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info