Bedienungsanleitung Bosch GWS 18-125 PL Inox (Seite 23 von 364) (Alle Sprachen)

786329

Zoom out

Zoom in

Vorherige Seite

1/364

Nächste Seite

24 | English

1 609 92A 3ZX | (7.11.17) Bosch Power Tools

A properly attached, undam-

aged quick-clamping nut can

be loosened by hand when

turning the knurled ring in an-

ticlockwise direction.

Never loosen a tight quick-

clamping nut with pliers. Al-

ways use the two-pin span-

ner. Insert the two-pin span-

ner as shown in the

illustration.

Approved Grinding Tools

All grinding tools mentioned in these operating instructions

can be used.

The permissible speed [min-1] or the circumferential speed

[m/s] of the grinding tools used must at least match the values

given in the table.

Therefore, observe the permissible rotational/circumferen-

tial speed on the label of the grinding tool.

Rotating the Machine Head

Before any work on the machine itself, pull the mains

plug.

The machine head can be

rotated with respect to

the machine housing in

90° steps. In this man-

ner, the On/Off switch

can be brought into a

more convenient posi-

tion for special working

situations, e. g., for cut-

ting operations using the

cutting guide with dust

extraction protection

guard 21 or for left-

handed persons.

Completely unscrew the four screws. Rotate the machine

head carefully, without removing it from the housing, to the

new position. Screw in and tighten the four screws again.

Dust/Chip Extraction

Dust from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dust can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dust, such as oak or beech dust, is considered car-

cinogenic, especially in connection with wood-treatment

additives (chromate, wood preservative). Materials con-

taining asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

Prevent dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Observe correct mains voltage! The voltage of the pow-

er source must agree with the voltage specified on the

nameplate of the machine. Power tools marked with

230 V can also be operated with 220 V.

Products sold in AUS and NZ only: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

When operating the machine with power from mobile genera-

tors that do not have sufficient reserve capacity or are not

equipped with suitable voltage control with starting current

amplification, loss of performance or untypical behavior can

occur upon switching on.

Please observe the suitability of the power generator being

used, particularly with regard to the mains voltage and fre-

quency.

max.

[mm] [mm]

D b d [min-1][m/s]

115

125

150

22.2

12000

10000

115

125 –

––

–12000

12000 80

75 30 M 14 12000 45

82 – M 14 12000 80

OBJ_BUCH-3330-001.book Page 24 Tuesday, November 7, 2017 2:23 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 18-125 PL Inox Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info