Bedienungsanleitung Bosch gws 20 180 (Seite 7 von 13) (Englisch)

390388

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

English - 3

Working safely with this ma-

chine is possible only when the

operating and safety information

are read completely and the in-

structions contained therein are

strictly followed. In addition, the

general safety notes in the enclosed booklet

must be observed. Before using for the first

time, ask for a practical demonstration.

■ Wear protective glasses and hearing protec-

tion.

■ Wear additional protection equipment for your

safety, such as protective gloves, sturdy

shoes, hard hat and apron.

■ The dust that is produced while working can be

detrimental to health, inflammable or explo-

sive. Suitable safety measures are required.

Examples: Some dusts are regarded as carci-

nogenic. Use suitable dust/chip extraction and

wear a dust respirator.

■ Dust from light alloys can burn or explode. Al-

ways keep the workplace clean, as blends of

materials are particularly dangerous.

■ If the mains cable is damaged or cut through

while working, do not touch the cable but im-

mediately pull the mains plug. Never use the

machine with a damaged cable.

■ Connect machines that are used in the open

via a residual current device (RCD) with an ac-

tuating current of 30 mA maximum. Do not op-

erate the machine in rain or moisture.

■ When working with the machine, always hold it

firmly with both hands and provide for a secure

stance.

■ Secure the workpiece. A workpiece clamped

with clamping devices or in a vice is held more

secure than by hand.

■ Always direct the cable to the rear away from

the machine.

■ Always switch the machine off and wait until it

has come to a standstill before placing it down.

■ For power outage or when the mains plug is

pulled, unlock the On/Off switch immediately

and turn it to the off position. This prevents un-

controlled restarting.

■ The machine must be used only for dry cutting/

grinding.

■ For all work with the machine, the auxiliary

handle must be mounted.

■ Hold the power tool only by the insulated

gripping surfaces, when performing an op-

eration where the cutting tool may run into

hidden wiring or its own cord.

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the op-

erator.

■ Use appropriate detectors to determine if

utility lines are hidden in the work area or

call the local utility company for assist-

ance.

Contact with electric lines can lead to fire and

electric shock. Damaging a gas line can lead

to explosion. Penetrating a water line causes

property damage or may cause an electric

shock.

■ For work with grinding or cutting discs, the pro-

tection guard 6 must be mounted. For work

with the rubber sanding plate 20 or with the

cup brush 23/disc brush/flap disc, the hand

guard 18 (accessory) is to be mounted.

■ Use dust extraction when working with stone.

The vacuum cleaner must be approved for ma-

sonry dust. When cutting stone, use the cutting

guide.

■ Do not work with materials containing asbes-

tos.

■ Use only grinding tools with a permissible

speed at least as high as the no-load speed of

the machine.

■ Check grinding tools before use. The grinding

tool must be properly mounted and turn freely.

Perform a test run for at least 30 seconds with-

out load. Do not use damaged, out-of-round or

vibrating grinding tools.

■ Protect the grinding tool from impact, shock

and grease.

■ Apply the machine to the workpiece only when

switched on.

■ Keep hands away from rotating grinding tools.

■ Pay attention to the direction of rotation. Al-

ways hold the machine so that sparks and

grinding dust fly away from the body.

■ When grinding metal, flying sparks are pro-

duced. Take care that no persons are endan-

gered. Due to danger of fire, no combustible

materials should be located in the vicinity

(spark flight zone).

■ Be careful when cutting grooves, e. g. in struc-

tural walls: See Information on Structures.

■ Blocking the cutting disc leads to jerking reac-

tion forces on the machine. In this case switch

off the machine immediately.

For Your Safety

1 609 929 F75.book Seite 3 Dienstag, 9. März 2004 9:19 09

8 • 1 609 929 F75 • 04.03

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 20 180 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch gws 20 180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info