Bedienungsanleitung Bosch gws 20 180 (Seite 8 von 13) (Englisch)

390388

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

English - 4

■ Pay attention to the dimensions of the grinding

disc. The mounting hole diameter must fit the

mounting flange 9 without play. Do not use re-

ducers or adapters.

■ Never use cutting discs for rough grinding. Do

not exert any lateral pressure on the cutting

discs.

■ Observe the manufacturer’s instructions for

mounting and using grinding tools.

■ Caution! The grinding tool runs on after the

machine is switched off.

■ Do not clamp the machine in a vice.

■ Never allow children to use the machine.

■ Bosch is only able to ensure perfect operation

of the machine if the original accessories in-

tended for it are used.

The machine is intended for cutting, roughing and

brushing metal and stone materials without using

water. For cutting stone, a cutting guide is re-

quired.

Slots in structural walls are subject to the Stand-

ard DIN 1053, Part 1 or country-specific regula-

tions.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architects or

the construction supervisor.

■ Before any work on the machine itself, pull

the mains plug.

■ For work with grinding or cutting discs, the

protection guard 6 must be mounted.

Protection Guard with Locking Screw

The coded projection 14 on the protection

guard 6 ensures that only a guard that fits the

machine type can be mounted.

Loosen the clamping screw 13, if necessary.

Place the protection guard 6 with coded projec-

tion 14 into the coded groove on the spindle col-

lar of the machine head and rotate to the required

position (working position).

The closed side of the protection guard 6

must always point to the operator.

Tighten clamping screw 13.

Protection Guard with Quick Clamp

☞

The protection guard is preadjusted to the

diameter of the spindle collar. If required,

the tightening tension of the clamping

bracket can be changed by tightening or

loosening the adjustment screw 7. Always

ensure that the protection guard 6 is

seated tightly on the spindle collar.

Open the clamping lever 8.

Place the protection guard 6 on the spindle collar

of the machine head and turn to the required po-

sition (working position).

To fasten the protection guard 6, close the

clamping lever 8.

The closed side of the protection guard 6

must always point to the operator.

Auxiliary Handle

■ For all work with the machine, the auxiliary

handle must be mounted.

Screw the auxiliary handle 4 into the head of the

machine according to the working method.

Do not continue to use an auxiliary handle if it is

damaged.

Hand Guard

For work with the rubber sanding plate 20 or with

the cup brush 23/disc brush/flap disc, the hand

guard 18 (accessory) is to be mounted. The hand

guard 18 is fastened with the auxiliary handle 4.

Intended Use

Information on Structures

Mounting the

Protective Devices

1 609 929 F75.book Seite 4 Dienstag, 9. März 2004 9:19 09

9 • 1 609 929 F75 • 04.03

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch gws 20 180 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch gws 20 180

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info