Bedienungsanleitung Bosch GWS 750-100 I Professional (Seite 19 von 301) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

708228

Zoom out

Zoom in

Vorherige Seite

1/301

Nächste Seite

20 | English

1 609 92A 36R | (29.8.16) Bosch Power Tools

Assembly

Mounting the Protective Devices

 Before any work on the machine itself, pull the mains

plug.

Note: After breakage of the grinding disc during operation or

damage to the holding fixtures on the protection guard/power

tool, the machine must promptly be sent to an after-sales ser-

vice agent for maintenance. For addresses, see section “Af-

ter-sales Service and Application Service”.

Protection Guard for Grinding

Place the protection guard 7 on the spindle collar. Adapt the

position of the protection guard 7 to the requirements of the

work step. Lock protection guard 7 by tightening locking

screw 8 with combination spanner 4/5.

 Adjust the protection guard 7 in such a manner that

sparking is prevented in the direction of the operator.

Note: The encoding keys on the protection guard 7 ensure

that only a protection guard that fits the machine type can be

mounted.

Protection Guard for Cutting

 For cutting with bonded abrasives, always use the pro-

tection guard for cutting 14.

 Provide for sufficient dust extraction when cutting

stone.

The protection guard for cutting 14 is mounted in the same

manner as the protection guard for grinding 7.

Auxiliary Handle

 Operate your machine only with the auxiliary handle 3.

Screw the auxiliary handle 3 on the right or left of the machine

head depending on the working method.

Hand Guard

 For operations with the rubber sanding plate 17 or with

the cup brush/wheel brush/flap disc, always mount the

hand guard 16.

The hand guard 16 is fastened with the auxiliary handle 3.

Mounting the Grinding Tools

 Before any work on the machine itself, pull the mains

plug.

 Do not touch grinding and cutting discs before they

have cooled down. The discs can become very hot while

working.

Clean the grinder spindle 6 and all parts to be mounted.

For clamping and loosening the grinding tools, lock the grind-

er spindle with the spindle lock button 1.

 Actuate the spindle lock button only when the grinder

spindle is at a standstill. Otherwise, the machine may be-

come damaged.

Grinding/Cutting Disc

Pay attention to the dimensions of the grinding tools. The

mounting hole diameter must fit the mounting flange without

play. Do not use reducers or adapters.

When using diamond cutting discs, pay attention that the di-

rection-of-rotation arrow on the diamond cutting disc and the

direction of rotation of the machine (see direction-of-rotation

arrow on the machine head) agree.

See graphics page for the mounting sequence.

To fasten the grinding/cutting disc, screw on the clamping nut

11 and tighten it with the combination spanner 4/5, (see sec-

tion “Quick-clamping Nut”).

 After mounting the grinding tool and before switching

on, check that the grinding tool is correctly mounted

and that it can turn freely. Make sure that the grinding

tool does not graze against the protection guard or oth-

er parts.

Mounting flange for grinding spindle

M 14: A plastic part (O-ring) is fitted

around the centring collar of mounting

flange 9. If the O-ring is missing or

damaged, the mounting flange 9 must

be replaced before resuming opera-

tion.

Mounting flange for grinding spindle

M 10: The mounting flange can be used

on both sides.

Flap Disc

 For operations with the flap disc, always mount the

hand guard 16.

Rubber Sanding Plate

 For operations with the rubber sanding plate 17, al-

ways mount the hand guard 16.

See graphics page for the mounting sequence.

Screw on round nut 19 and tighten it with the combination

spanner 4/5.

Cup Brush/Disc Brush

 For operations with the cup brush/wheel brush, always

mount the hand guard 16.

See graphics page for the mounting sequence.

The cup brush/disc brush must be able to be screwed onto

the grinder spindle until it rests firmly against the grinder

spindle flange at the end of the grinder spindle threads. Tight-

en the cup brush/disc brush with an open-end spanner.

Quick-clamping Nut

For convenient changing of grinding tools without the use of

additional tools, you can use the quick-clamping nut 12 in-

stead of the clamping nut 11.

 The quick-clamping nut 12 may be used only for grind-

ing or cutting discs.

Use only a flawless, undamaged quick-clamping nut 12.

When screwing on, pay attention that the side of the

quick-clamping nut 12 with printing does not face the

grinding disc; the arrow must point to the index mark 23.

OBJ_BUCH-2565-002.book Page 20 Monday, August 29, 2016 2:42 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 750-100 I Professional Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info